I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!
Overall an easy repair. Belt came with diagram for easy threading the belt.
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement. Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
5 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor was bad
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting
i could not perform the repair because despite using the proper id numbers, i received the wrong parts from kenmore three times in a row. now i am trying to return the wrong parts which cost me 120.00 for the start switch, and the knob for the switch, so far. the switch was 40.00 the simple plastic button was (wrong) 40.00, and the wrong unidentifiable part, suposedly correct one, which also was 40.00. this, with the original 40.00 wrong switch amounted to the 120.00 that i am still trying to have returned. otherwise, the fix should be quick and simple, o yeah, its been three months.. you tell me if i am satisfied....
Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.
Drum not turning; accompanied by loud "screeching" sound.
Followed instructional video provided for this type of repair after diagnosing problem via of 'troubleshooting' on PartsSelect site. Simple, safe, and relatively easy (minimal mechanical knowledge helpful). Second time using PartSelect; washing machine repair ~ 6 mo. previous. PartSelect was spot-on with that repair as well, saving hundreds of dollars.....my go-to site for appliance repairs and pats....make it yours as well and you will NOT be disappointed! Fast, prompt shipping.
Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.
I Picked up the two front corners up, after removing the 2 screws from the vent and the 2 screws that hold the door switch in place, then I disconnected the old switch and put in the new one. Just the opposite of how I took it apart. Very simple and it works great!! Thanks
Part came in about 3 days. After reading and checking what was wrong with the Dryer -- which i read if there was no noise coming from the dryer it was the door switch, Looked up the part number and then saw a video that showed how to install the door switch. The video was so informative and precise on everything you had to do and easy Saved money on a service call.