YKESV908PM01 KitchenAid Range - Instructions

Followed a video. Followed instructions

Remove the oven from the wall
Remove the rear panel
Remove the 2 bottom panels
Lift and fold back the insulation
Remove the element enclosure
Replace the element
Reverse the steps to assemble

* the oven would not preheat and the top elements were working

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem

Removed old racks, installed new racks. Recycled old racks.

Quickly

Remove and replace oven door hinges. Disassembly of oven door unit required. Step by step instructions available on youtube.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

First I looked at how I would get to the blower - this took 15 minutes. I removed the grills to access the burners. Then I removed the burners that took approx. 15 minutes. I then had to remove the knobs for the burners. Next I had to remove the front control panel which had 2 screws - (did not disconnect any wires but supported it). Next I had to remove the side trim. Next I removed 4-5 screws that secured the upper burner range top. Next I removed the side panels which has a braket on the lower forward side and 2 rear screws on each panel. Next I had to remove the aft backspash guard. At the back I had to remove a support braket that had several screws - then I had to remove the exhaust fan back panel guard. Next I had to remove approx. 7 screws on each side of the stove that supports the burner valves. Then I lifted the left side most closest to the blower. This gave me access just enough to remove the mounting screws (4) and to remove the 2 wires. There was some cushioning material which I found inadequate to prevent any vibration when the fan and the valve support top sits on the blower - so I doubled it. Then I reinstalled everything. This job took me 4 hours. I suggest calling a Kitchenaid repair technician and not doing this yourself. Unless you are a mechanically inclined and really like frustration.

Pulled out stove and removed side panel, then removed old fan unit. Installed new fan unit and replaced side of stove then slide back in place, stove runs even more quiet than when it was new. And obtaining the new part from Partselect was even easier than dealing with a part store where you stand at the counter. This service really has the part down pat for us layman repair people.

After turning of the breaker for the oven, I pulled out the oven, removed the back panel. The High-Temp thermal cutoff was attached to 2 wires, which I unplugged, and then removed the cutoff by removing two screws. I then replaced the part in reverse order, pushed the oven back into the cabinet, and turned the breaker back on.

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

Using the video from PartSelect I followed the steps shown. Sliding the range out was difficult so I tilted it forward resting the frame on a 5 gallon plastic bucket. I did have to crimp on a new terminal. The repair was straightforward.

Repair was really simple. Saw that the outer shielding on the existing heat element had degraded and ordered a new element. Part was shipped to my house in two days. Actually took me longer to get the oven door off than to replace the element because the left bracket on the door was slightly bent. Element came out after removing 4 screws and disconnecting 4 wire terminals. I was able to do the repair inside the oven and did not have to pull it away from the wall as the wires were long enough to pull through. I used some painter's tape to tape down the disconnected wires so they would not fall back behind the oven. Then I used a needle-nosed pliers to slightly crimp the wire terminal to the heat element and screwed in the four screws. That was it! Never did this type of repair before and it was really easy. Also estimate that for my 20-25 minutes of work I probably saved over $200 in parts and labor if I hired someone to do it.

Turned off circuit breaker to oven
Removed oven door
Removed screws of reflector plate and top and back of oven
Gently pulled element out and down slightly
Removed slide crimps on wires
Replaced reflector plate on new element
Connected slide crimps on wires
Screwed reflector plate with new element to top and back of oven
Done. Total time 22 minutes
Tested and it’s perfect!

The oven is a KitchenAid convection oven with 4 panes of glass. The front, two inner glass panes that aren’t “touchable” and the interior glass that is the one that takes the heat from the oven and which you can clean easily - this is important because the descriptions of the glass all say “inner glass”. This is door #3 in the diagram that measure 10 x 22”. Which I cracked when I was pouring water into a pan to create steam for bread baking (lesson learned).

Because of the age of the oven, to remove the oven door it was necessary to place “pins” (we use medium screws) into the hole behind the door latches. Then were able to lift off the oven door. (We saw some videos on YouTube)

We placed the oven door on the counter top and removed ALL screws that held the door at the bottom and around the casing - KEEP these screws separate by where you’ve removed them so you replace them into the proper section when you reassemble the door. Each glass you remove has slots that hold them in their proper places. I recommend taking a picture BEFORE you take out each glass as there are brackets that need to go in proper order and you don’t want to forget the order.

We had to flip the door over in order to CAREFULLY remove the casing and access the different inner glass sections (took the opportunity to really clean them). Gathered the broken glass pieces into a paper bag and vacuumed the fragments. Then we were able to place the new interior glass from PartSelect, and reassemble the oven door. It’s perfect!

This took some time most likely because it’s a very old oven and you need to be methodical. I was just glad to be able to get the part - not yet ready to replace the oven.

BTW, originally I was guided to order glass #7 which is one of the inner glass panes that you cannot touch - unless you take apart the oven door - The exchange for the proper door was handled very quickly and easily. Hope this helps.