Models > YKEBC107KM0 > Instructions

YKEBC107KM0 KitchenAid Oven - Instructions

All installation instructions for YKEBC107KM0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the YKEBC107KM0
16-30 of 108
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

inner glass broken

  • Customer: melody from Beltsville MD
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 12 of 16 people found this instruction helpful
Thanks to those who replied to my intitial distress call...because of them I had the courage to attempt the repair.
First I flipped the main electrica breaker.
then I removed the screws from the main door. The next step was to pop out the pins holding the hinges. I couldn't do that no mater how much WD-40 and lubricant I used, or how hard I tapped center mass.....SO I took all the OTHER components out staring with the side facings. (1 screw right left and 2 for bottom.)
Next I took the screws holding the door together out -- then the two screws holding the clamps on the bottom of the door. At this point I lifted off the the front facing of the door by the handle and placed it with its glass, to the side.

I then had access to the two inside panes of glass. They are secured with a metal plate screwed into the metal of the inner door. When I removed the two screws securing the plate, two plates dropped to the floor and it was fortunate I was holding the glas securly as it two would have dropped.
Next, I cleaned each of tpieces of glass with oven cleaner and set them carefuly to the side.(they were crusted with brown) Lastly I wiggled the broken glass out of the small inner window, working from both the inside and the outside of the window. Becuase I couldn't open out the door.. this was an extrememly time consuming activity..but do-able.

Once the inner glass was in screwed one of the screws o the clamp plate so I could rest the glass while screwing in the second screw. Once screw two was in place I took out the retaining screw and replaceed in with the glass clamped between. Aftern that the tough stuff was done and I just reassmebled all the door parts.

This SHOULD have been much simplier! IF I could have removed the hinge pins as directed.

Anyway, mission acomplished. Oven works fine.
Thanks!

Replaced our oven racks, becasue I (the husband) forgot to remove them before the "Self-Clean" process and they turned colors just as the instruction manual said they would !!

  • Customer: Kevin from Joliet IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
Easy, pulled out the old dis-colored racks and slid the new ones in. I was VERY happy with the quick receipt of my order. If I ever need parts again,this is where I will go

After using the self cleaning feature the oven would not work

  • Customer: Sherrill from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
Don't, Don't, Don't!!!!!!! call a repair man to replace the thermo fuse. If you are able to use the T.V. remote and crack a twist top off a cold beer, then you can DO this. I am 47 years old and half retarded and my 84 year old neighbor and I completed this task in 12 minutes. Turn off the breaker panel, pull the oven out, (it is hard wired). We placed it on a 4 wheeled dolly. Unscrew 11 screws, pop the panel. The fusee is at the top/center with two screws holding it. Pull the two wires off, screw it back in place. Put back the panel & 11 screws. Put the oven back in place. Turn on the breaker and you are done. PS Tell your wife or girl friend this might take an hour or so. Send her to the store for a six pack & steak.

Oven door stayed locked with oven light on.

  • Customer: Larry from Dacula GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
Problem : One of the door latch center spindle locking clips had sheared off when the door was slamed shut. The latch then lifts up causing the light switch stay on and latch to stay engaged.
Repair: REMOVE POWER TO STOVE
1/ To open the door slide your fingers or a bent tool right to left to slide the latch to open the door.
2/ Go to the bottom of the open door on both sides and remove the screws. Then lift the plastic covering strips away.
3/ Remove the screws on both outsides at the top of the removed tracks
4/ Now you can lift the front panel with the clock up and off.
5/ Remove the 3 plugs on the back of that panel .
6/ Remove the 2 screws just above the latch.
7/ Remove the latch assemby.

Reverse order to install new latch & door.

Tempered Glass on oven door cracked; replaced the glass and insulation.

  • Customer: Leon from Atascadero CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 10 people found this instruction helpful
I removed eight screws to disassemble the oven door. I removed the old insulation and the brackets that held class panel in place. I installed the new insulation, tempered glass and reassembled the oven door.

Inside glass of the oven cooled too fast and cracked

  • Customer: Grant from Anaheim CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
The repair is straight forward. The only complication anyone seems to be having is removing the door ( which is a definate must to do this repair properly). So I would like to add some details about removing the door. The manuel shows the allen wrenches going into what looks like the hinge itself to release it from the oven. This is not the case. The holes that the 5/32 allen wrenches go into are actually behind the hinge itself. I wrapped the allen wrenches with some painter tape to protect the surface of the door and oven from scratching. Then, simply insert the short end of the allen wrenches, one on each side, into the holes behind the hinge. Then as it shows in the manuel, gently close the door. But not all the way. As you get about 80% closed you'll feel resistence. That is the time to grasp the bottom of the door and start to lift it from the bottom, while stablizing it with the other hand holding the handle on the door. The hinge will start to release from the oven as you continue to press it closer to being all the way closed. The hinges will release if you are doing this correctly before the door can be all the way closed.

Hope that helps. Otherwise, once the door is off. Unscrew all the screws...pay special attention to what you are unscrewing and how it all fits together, because you're going to have to put it all back together again. Some of the glass is held in place with clips and some of it is not. Just lay it down flat and be careful to not force anything in or out and you'll find it quite easy.

Oven Would Not Heat After Auto-Clean

  • Customer: Jim from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.

Oven lights out

  • Customer: Rex from Amarillo TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
There are two lights in this model oven. The glass will open by pulling outward on the near end. Since these are halogen bulbs I used a clean cloth to hold the bulb while replacing. Bulbs are expensive especially when purchased from Kitchen Aid dealer. I got two bulbs from PartsSelect delivered in two days for considerably less.

Double ovens and ONLY 3 oven racks.....

  • Customer: Paula from Fairview TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
No repair - just open the box and put the rack in my oven - voila - repaired!!! BUT let me tell you PartSelect sent the right part at the best price and I received it even ealier than I expected!!! I can DEFINITELY recommend these people and I do that very sparingly!!!! THANX!

Inner glass to oven door shattered

  • Customer: Robert from Forsyth MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Removed the 6 screws securing the door and inner frame unit. Lifted off the frame and inner glass unit. Then, after cleaning all the broken glass, put the new glass in; first reattaching the inner frame and then the outer door cover.

Broken inner door glass on wall oven

  • Customer: Ronald from Scottsdale AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
The inner glass on the wall oven shattered (apparently a common problem). Rather than look at a new $2-3,000 oven, I found the part for around $30. The repair was actually fairly easy, just had to be careful with the glass panes.
I did not remove the door completely, just worked on it either open or closed, depending on the step. First I loosened the two screws on the bottom of the door (when closed). Then I removed the four screws on the inside of the door and the two on the top part of the door (2). This allowed the outer panel to slide out and be removed.
Then there are two middle panes, held on by small clips with two screws in each. Remove one at a time, being careful not to drop any of the glass on the floor! Remember the order of the glass and the clips, so you can replace in the same order. (Now's a good time to clean all of the inner panes also, and to vacuum out the interior of the door.)
Lay these panes aside, and you should be to the broken inner pane, held on by a metal panel--again remove a couple screws, the panel, and remove all the broken glass. Be careful to retain all the insulation around the glass, and replace the glass, then the metal panel, the inner panes, and the outer door panel in that order. The outer panel should slide into place if you remove one clip and screw and start on one side, then replace the clip.

Oven door latch would self-activate the door-lock feature for all operatons making it impossible to use the oven

  • Customer: Anthony from Lambertville MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 10 people found this instruction helpful
My electric oven is a built-in. First I turned off power to the oven.

Then, I removed the oven door as instructed by Kitchenaid, next I removed the screws that held the concealing-sleeves on each side of the oven opening. Slid down the sleeves, loosened the exposed screws on each to allow the oven to slide out. Slid the oven out abut half way to expose the top. Removed the metal sheeting from top of oven to expose area where door latch assembly was secured. Removing the sheeting was made easier by removing the screws on each side of the control panel and lifting the panel out of the way.

The latch assembly is held in place by two screws through the front of the plastic venting. Identified the connections to appropriate points before I removed the wiring, removed wiring and attached to points on the new latch assembly.

Secured latch assembly to plastic vent, secured sheeting to top of oven, placed conrol panel back in place, pushed oven back and secured with screws.
Slid sleeves into position, secured with screws and replaced oven door.

Inner glass door cracked

  • Customer: Carmen from Redlands CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 5 of 7 people found this instruction helpful
Kept removing screws and pulled things out until I got to the inner glass.
Yep, clueless and never did this before.
Put everything back in the opposite order of taking it out. Wala it's fixed.
Repair people wanted over $300 for parts and labor. However, with Partselect I was able to fix it for under $50.00 Well worth it!
Carmen

REPLACE HALOGEN BULB

  • Customer: ROBERT from ELMIRA NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 13 people found this instruction helpful
USED FLAT TIP SCREW DRIVER TO PRY FRONT CLIP HOLDING GLASS COVER OUT OF POSITION. PULLED OUT DEAD BULB AND PUSHED IN NEW ONE. SLID CLIP BACK ON GLASS COVER AND SLID BACK INTO PLACE. SIMPLE..

Replacing inner glass on oven door

  • Customer: Kel from Denver CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.
All Instructions for the YKEBC107KM0
16-30 of 108