YKCMS145JBL0 - Instructions

Pried cover off bottom-center of microwave. It seems to be either glued or lightly tack welded. Removed 2 small Phillips screws to remove motor. Disconnected electric feed by hand. Don't let go of electric wire or small screws. They will be hard to retrieve from behind the rest of the metal base. Reverse process to install new motor. Didn't try to put small cover back on.

Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.

very easy just put the tray on the turntable. excellent delivery service arrived sooner then expected.

I started by calling a reputable service company to diagnose my problem. The repair tech told me it was the magnetron and it was a "very difficult" repair that required two people because the over-the-range unit needed to be taken down. I asked for a detailed estimate. He quoted $550 including parts and labor. After he left, I researched the part costs on this site and realized his costs were very inflated. I purchased the magnetron for $220. It arrived at my door two days later. Installation was very easy. First, I unplugged the unit. Then, while my wife was making sure it did not fall off the wall bracket, I unscrewed the two mounting screws from the top of the cabinet. I lifted the unit down from the wall and set it on the kitchen counter. The shell needed removed from the microwave which involved about 20 screws. This provided access to the magnetron on top. The magnetron is secured by five screws and a plug. I unplugged it, unscrewed it, and removed the old part. Then, I installed the new magnetron, and tested the microwave to make sure this did the trick. It worked. I put the outer shell back on the microwave and cleaned the microwave. (This is a great opportunity to clean the areas you do not typically see!). I then remounted the unit and plugged it back in. Saved myself a bit of money so I took the family out to dinner and a movie to celebrate. Microwave was in working order for heating up left overs the next day! Thank you!!!

Eight screws off the bottom exposed the cover plate. Easily found the motor location the looked up the item number and verified data and ordered the part. Replaced the motor, tightened the screws and flipped it upright. Plugged it in and the lights came on. Set a time pushed start and smiled! The eagle had landed!!!!

Ordered the switches from Partselect, arrive in two days. Had trouble removing the plastic connectors from the old switch terminals, one of the plastic protectors broke, but was able to reuse it. It took a little figuring out how to remove the existing switches. Must push in a tab and rotate the switch on a little pin, then remove. Must be careful not to break the plastic tabs holding the switches in place. Replaced all (3) switches at the same time. All in all it was pretty easy.

It literally took me longer to unpackage the fuse than to install it. I removed the outer shell by unscrewing the five screws, lifted it off and set it aside. The old fuse was readily visible so I pulled it out and put the new one in its place. I set the shell back on and replaced the screws. I plugged it in and ran it for 30 seconds while still in the shop just to make sure that solved the problem and presto - it worked like a charm. A $20 part saved me from having to purchase a new microwave (sadly, I had to break the news to the wife).

1. Remove the trim frame off of the front of the cabinet (4 Phillips screws). At this point, take glass plate and turntable frame out of unit. 2. Slightly lift the unit off the cabinet frame (which is attached to the cabinet) so the feet on the microwave allow the unit to clear the frame and then remove microwave from the cabinet. 3. Once slightly removed from the cabinet, unplug the unit before completely removing it from cabinet. 4. Take 2 Phillips screws out of the side panels. 5. Take about 6-7 T20 Star Pin screws out of the back of the panel. (This may require you to purchase this special tip if you don't have it in your toolbox). 6. Slide the microwave cabinet toward the rear of the unit (the front portion clips into the frame ... don't try prying it off because you'll damage the unit). 7. Completely remove the microwave cabinet housing. 8. Be careful not to damage or catch any internal wiring inside the unit while the cover is off. 9. Turn unit on it's back and remove 4-5 Phillips screws holding the bottom cover in place. Remove bottom cover. 10. Now notice that the turntable motor is completely exposed. 11. Remove the wiring harness from the motor (notice which connection clip has the black wire). 12. Remove the one Phillips screw holding the motor to the frame. 13. Clean around the area in case food spills may have gotten into the area. 14. Insert new motor, put Phillips screw back in and attach power connection. 15. From this point on, just reverse steps to re-assemble microwave and put back in cabinet. 16. Test new turntable motor. 17. Enjoy the smile from your wife because she can now use the microwave!

I removed the outer cover of the microwave and removed the bottom palte to access the small motor. i unplugged the old motor from teh wiring connector, removed (1) screw and motor came out. I reversed the proceedure with the new motor and it was finished.It was a piece of cake.

removed microwave cover screws, unplugged motor, screwed on new one

Unplug.Take off the external cowling from the back of the unit by removing the torx security screws. Tip: instead use a thin screwdriver blade to unscrew the torx screws, or knock out the center pins of these screws. Remove the bottom panel. The replacement motor is attached with one phillips screw, re-attach wires to motor - polarity doesn't matter. Re-assemble and you're finished.

Partselect sent me the right thing in two days! The whole process was easy as pie.

The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .