YIED7300WW2 Inglis Dryer - Instructions

Saw no heat, web said probably the fuse. Replaced the fuse. Nope. Second guess was the thermostat at the exhaust. Replaced that. Nope. Finally got to actively troubleshooting and isolated one of the thermostats near the heating element. Replaced that and everything is fine. So now I have a good spare fuse and thermostat for the next repair. There was one tool I wished I had, a socket small enough to open the back. I had to use pliers and that was a pain. Other than that the repair was almost trivial, just unplug the bad one and plug in the good one.

Removed back panel of the dryer and located the thermal fuse. Disconnected two wires, and removed one screw holding the fuse in place. Installed new fuse and reassembled. Dryer works like a champ again.

I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter

Disconnect the power cord. Unhook the dryer vent hose. Remove the back. Find the Thermal Fuse. Use a ratchet and socket to remove socket head screw that holds the Thermal Fuse in place. Disconnect one of the two wires from the old Thermal Fuse and attach the wire to the new Thermal Fuse ensuring the wire is placed on the same end of the new Thermal Fuse as the old Thermal Fuse. Repeat procedure for the remaining wire and screw Thermal Fuse back in place. Replace the back, reattach the dryer vent hose and connect the power cord.

Repair was extremely easy. I looked on your parts web site and found my model number, read what the common causes of dryer not heating. I purchased both the Thermistor which I knew was bad after using my Omh meter and found a open circuit, and bought the High limit thermostat as maintenance. In addition to these parts I also purchased the heat element assembly which I could see was broke. In stalling all three parts was less than 15 minutes, less than $100 and WOW less than two days delivery !!! Great job I will re-order from you again! KIm Faught, League City, Texas

unplugged unit, removed the back panel replace thermo fuse and replace back panel, plugged electric cord back in and we were back in business. real easy fixx

I followed the video on the website, removing the back of the dryer, then located and removed the thermal fuse, replaced it with the new one..... Presto, it worked... Replaced the back of the dryer and was good to go... Thank you Part Select

replaced thermo fuse. not the problem. not sure how to test for next step. timer, cycler tumbler all work just won't fire up.

Getting the fan off proved to be quite an issue. on my model, it loosened in the clockwise direction. I ended up having to completely pull the motor and clamp the unit in a vice before I was finally able to gett itloose.. Hopefully yours will not be such a problem....

I followed the instructions from the video and had no problems

Dont believe that '1.8 days average delivery' time. if you need to parts in days, get them delivered overnight. Otherwise it was very easy to seals, rollers and belt. Only advise is on the seals. you might want to sort of stretch them out a bit so they are easier to slip on because once you have the glue on there it is harder (and messy) to be stretching them on

I watched your YouTube video about trouble shooting dryers, and found that the problem was my thermal fuse was out. My exact model of dryer was used in the video. I ordered the part and replaced it following the instructions on YouTube. Since the video was so helpful, I decided to order my part from your company

Most of the time was spent just getting behind the dryer and removing the back panel. It was also a great time to vacuum the area. If you're not working in tight quarters, this repair is really easy. The fuse is not hidden and requires no tools to install (only a wrench to remove the back panel). It started working right away & the part cost significantly less than a service call (about nine bucks + shipping).

Got the latch kit, found the correct one, popped it in...dryer works! Thanks....

The kit turned out to be missing a 7.40" 4" diameter vent that was needed so ending having to get my plumber to use what was there with a "cut and paste" job - took him over an hour. He did say that had the right piece been there, it would have been easy.