YGEW9200LW0 Whirlpool Dryer - Instructions

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.

Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.

Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.

I purchased a replacement "Thermistor", "Electrode", and "Door Catch Kit" for my 2002 Kenmore Elite He3 electric dryer. I watched several repair video's but wasn't thrilled with the instructions or the high degree of "remove and replace" of components, just to get the the parts I wanted to replace. I took the top panel off my dryer and removed the troubleshooting guide. It showed that the Thermistor, Electrode, and several other components, could be accessed from the front lower panel. I removed the panel, and then the blower cover (two screws and a clip). This gave me access to the Thermistor. It was a little tight, but I removed the part with little problem. Unfortunately the Thermistor the company sent me for my dryer model was incorrect. Not only would it not seat flush in the oblong hole in the blower housing, but the male electrical connectors were a 16th to an 8th inch too wide for the female connectors on the dryer. I ended up cleaning the old Thermistor and re-installed it. We'll see what happens. The Electrode was no problem, I simply removed the lint cover from inside the dryer (3 screws), and carefully pulled the slack in the wire harness enough to remove the electrical connections from the ends of the Electrode. That could have been done without removing the lower panel, but unless you've done it before, I'd recommend removing it, and the blower cover. It gives a better view of the connections. The electrodes have a small metal catch that holds it in the plastic vent cover. You can see it on the replacement part you'll have before you remove the old one. The door catch's are a no brainer. You can look at the new ones and see how that fit. They also come with well written instructions. Good luck with your repairs.

Exactlyt how your video showed me. I was a bit skeptical, but it was the easiest repair ever.Thank you

Using some advice here on this website, and a youtube video found by searching for 'idler pulley replacement' I was able to fix my dryer! Taking off the screws was simple, I used a cordless drill. I have some trouble removing the kick panel, and bent the latches, so there is a small gap between the dryer door panel and the kick panel, but it still works fine. Of note, you DO NOT need to remove the back panel, something I did and cost me some time. I am a bigger guy, so maneuvering on the floor to rig the dryer belt around the new idler pulley "in the dark" was cumbersome, but doable. All in all, an easy enough project for under $30 and less than an hour of my time. Kudos to this website, first, for the super fast shipping, and secondly, the reviewers who posted some instruction. Great job!

Using Partselect to troubleshoot, I determined the heating element was shot. Upon receiving the part, I disassembled the unit, inserted the new element and reconnected everything. It couldn't have been simpler and saved me a ton of money.

Disconnect the dryer from the power source and vent hose. Using the nut driver, remove all hex screws and the electric access panel from back of dryer. Loosen the electrical service cable clamp screws with philips screw driver and disconnect the ground wire. Remove the top panel from the dryer cabinet and the screws that hold the electrical bus in place, then remove the back panel from the dryer. Feed the electrical cable through the cable clamp and rest the back of the dryer against the side. Remove the tri-ring and old idler pulley, then clean and lubricate (WD40) the axel, and install the new pulley and tri-ring. Replace the back panel and all screws.