Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YG226LV > Instructions

YG226LV Magic Chef Dryer - Instructions

All installation instructions for YG226LV parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the YG226LV
61-75 of 826
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No Heat

  • Customer: NICHOLAS from PARMA, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 8 of 11 people found this instruction helpful
I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (it should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.

noisy blower wheel

  • Customer: Ernie from St Ignace, MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
unplug dryer---pop the top up---remove 2-1/4 metal screws that attach front to sides---unclip door switch & wires-lift up on front & set it aside--locate blower housing-remove 6-7 1/4 & 5/16 head metal screws--tough part is i had to buy a snap ring plier to get snap ring off motor shaft--use regular pliers,remove spring clip from blo-wheel hub--wiggle & pull blo-wheel from shaft--befoe re-assembling,,vac out all areas inside dryer case-carful not to damage wires & heat element--when clean re-assemble in order removed--also when ordering parts,,my dryer is series 11 (first two digits in serial #)--parts list showed wheel for series 10 & another for series 12---per instructions from a very nice lady on the other end of the parts select phone,always select the lower series--i my case,series 10

Dryer belt broke- drum would not turn

  • Customer: Ronald from Oakdale, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner sprung to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..

broken pulley and belt

  • Customer: Raul from cypress, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 13 of 27 people found this instruction helpful
Before anything else, I would like to thank your company for a quick response and fast delivery of the parts that I ordered. Ordering parts from your company saved me a lot of money. The repair took me about 15 min. First I removed the two screws that hold the front cover and then I pulled out the drum and replaced the broken pulley, then I put back the drum and the belt in place and then I put the cover and screwed back in and now I'm back washing and drying pile of clothes.

extremely noisy operation

  • Customer: Paul from Daly City, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
unplugged unit, opened lid, removed 2 screws & door switch from front panel, removed front panel & drum.
Removed clips & washers from rear roller shafts, removed 2 screws (each) attaching rear roller shafts to rear of unit. Replaced rear roller shafts, thrust washers, rollers & clips. Removed clip from belt tensioner idler arm, replaced idler pulley wheel & clip.
pulled tensioner toward motor side and locked in place with broomstick. Placed new belt over drum & installed drum/belt into unit, engaging rear drum lip over new rear drum support rollers. Guided belt
over motor shaft and slowly released broomstick to
tension belt. Turned drum by hand to ckeck belt tracking. Reinstalled front panel & door switch, installed 2 screws holding front panel to case. Closed lid. Plugged unit in & tested for proper operation-OK.

gas dryer would fire, but shut down before getting warm enough to dry clothes

  • Customer: Glenn from Ossian, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 6 of 6 people found this instruction helpful
Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. Then closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.

Klunking noise and poor drying

  • Customer: Harry from Atco, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 6 of 6 people found this instruction helpful
The top was hard to figure out but I found that it pops off at the front with a flat screw driver. Be careful not to scratch the paint. I found that a rear drum roller was bad and the drum seals were deteriorated. I ordered a new belt, roller kit, front, and rear seals. This way I hoped I will not have to take it apart again. The seal were the hardest parts to replace. Make sure you look and remember how they were on before removing them. The directions were not to clear on the seals. The rest were good. It is much better to do it once. Take a picture if possible, it might come in handy as I took mine apart a week or so before the parts came in. I also cleaned out all of the accumulated lint buildup with a shop-vac, including the vent pipe, heater area, and front door. When I was done with this it worked like brand new.

dryer drum belt broke

  • Customer: Paul from Athens, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
I needed to remove the front lower cover, very easy as it is held on with clips only so I used a flat head screw driver to pop it off. I had to remove the lint filter and then there are two screws attaching the top cover of the dryer to the internal lint filter tray. The top of the dryer can then be opened front to back I again used the flat head screw driver to pop the top open as it has two clips at the front corners. It helps to have someone to hold it open or a rod of some type to keep it open. You can now lay the belt on the top of the drum and work it down the back side by pulling forward on the drum itself to seperate the drum from the seal that presses aginst the back side of the drum. I then went from the lower front to retrieve the belt now draped over the drum and pinched the belt to pass it through the tensioner and over the drive pulley. looking at it from the front the belt will come down the right side of the drum under the tensioner pulley around the drive pulley across the bottom of the drum and up the left side. The belt sits almost in the middle of the drum not against the back lip where there is a groove that might be confused as a place for the belt to ride that is where the seal sits then reverse the process to reattach the top to lint tunnel and reattach front cover and you are good to go . i would suggest vaccuming any old dust/ lint whlie everything is open as this reduces the chance for catching on fire I was supprised as to how much lint was loose inside the dryer cavity itself and our dryer is gas and the flame is an open flame.

Dryer would not come on

  • Customer: Max from Wylie, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 6 people found this instruction helpful
Verified power to the dryer with a volt meter. Identified the high limit fuses under the top cover. I used an ohm meter to determine the fuse located on the heater housing assembly was bad. The fuse located at the top (blue label) was not bad but I changed it since a new one was sent in the kit. Reassembled the dryer and it has been working ever since. Found the problem on a Monday and ordered the part. Received the part on Wednesday and the problem was solved. Cost me about $31. Would have been triple that if a repairman would have been called. Thanks PartsSelect

Dryer was squealing while spinning

  • Customer: Dale from YONKERS, NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 6 of 7 people found this instruction helpful
I followed the directions from a post on parts select that somebody had previously written and my repair worked out perfectly. I removed the top / lid of the dryer by placing a flat head screwdriver underneath both top front corners which was relatively simple. I then removed the entire front door of the dryer by disconnecting the electric wires for the door which again was a very simple procedure. The tumbler was now exposed at which time I removed the belt (I took a picture of the belt setup for later reassembly) and lifted the tumbler off giving myself easy access to the rear drum rollers and front drum pads. I was able to see that the wheels were worn and definitely the cause of the squealing. I changed out the wheels with replacement wheels which was self explanatory. The front pads were in good shape but I figured that at this point it would serve me well to replace them also which I did. I then reset the new belt (another part that I opted to change while I had the opportunity) on the tumbler with the picture in hand and had no problem. This step did require two people but still not a difficult step. I then put the door and lid back together and now had myself an extremely quiet dryer and a piece of mind that new parts were installed. All in all pretty easy repair.

Dryer declined to work- at all

  • Customer: William from Beacon, NY
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 6 of 7 people found this instruction helpful
Web search to determine probable cause then search to find parts. Parts Select came through with the parts and quickly. Opened the top of the dryer (after disconnect from power-hate the smell of burning flesh) and found the parts that had up and died. Removed two screws for first part then one more and a lot of cursing to remove the other. Reassembled in reverse order, more cursing the tight space. Dryer back in service, wife happy. Only minor blood loss from sharp parts of machine. Success!

Originally Noisey While Running

  • Customer: Gary from Park Hills, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 10 people found this instruction helpful
Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued on underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.

No Heat After 10 Minutes

  • Customer: lawrence from GROTON, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 6 of 7 people found this instruction helpful
Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

loud rattling and grinding noise when drum is turning

  • Customer: Steve from Green Bay, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Always begin repairs by unplugging the power cord from the power outlet! First, push in the 2 taps under the dryer top to lift it up and secure it at a 90 degree angle. Remove the door light switch from the retaining clip and let it hang to the outside of the dryer. After removing the 2 scews inside the top front, remove the front dryer cover. Next, remove the screws holding the blower cover and set it aside. Using a pair of plyers, remove the hose clip from the blower axle. Use a c-clip tool to remove the c-clip and pull out the blower wheel. Use a vacuum attachment hose to remove lint and other dirt from the wheel housing and dryer. Apply a light dish soap to the motor axle and slide on the new blower wheel. Replace the blower housing cover, front dryer cover, light switch, and close the dryer top, making sure to allign the pins and holes near the lid clips that secure the dryer top. Plug in the dryer power cord and you are set to go! Retire to your favorite lounge chair, grab the remote, and tell your wife that it is OK to "test" the dryer! However, do not attempt the last step until AFTER you have cleaned up all the mess you made while making the repair!

Lint screen assembly holder had broken

  • Customer: George from Vernon, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
First I removed the 2 screws located on front panel securing dust collector in place, then I removed the two screws on the side of the dryer that secure the front panel. I also "popped" the top
of the dryer from the front panel. The front of the panel was then detached from the dryer. I thenpulled the gasket away from the collector, removed the old one and installed the new collector. Part of the kit also contained a new gasket to the exhaust duct, I merely removed the old gasket and installed the new one.. All this was notas hard asit sounds. The diagram from PartsSelect site helped
All Instructions for the YG226LV
61-75 of 826