YG226LV Magic Chef Dryer - Instructions

I watched the attached video that was with the belt I ordered and it took less time to do the repair, then it did to watch the video. The video was very helpful.

2 screws at lint tray 2 screws on back pick up top 2 screws in front under top lid separate front from drum slip in new belt screw front back to top route around tension pully put other 4 screws in complete so dry something

Popped top up Took front panel screws out. Looked for other damage. Put belt around the tumbler and got it hooked up. Grew an extra set of hands and re assembled front the checkd seals to make sure they where on and put top back down... Process is a pain in the butt i reccomend socket set channel lock pliers and a cold beverage or two

Removed top and front panels, lifted front of drum, slid new belt on drum then thru tension and motor pulleys. reassembled.

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

Had to lift the top and take the face of the dryer off. Then took the tumbler out and the blower wheel apart. This was all very easy I replaced the belt and cylinder seal since I had it all apart my dryer is about 8 years old so I only want to do this one time. I put it all back pluged it in and the dryer works just like the day we bought it. So for under 80.00 our dryer is fixed. I will use this site again if I need anything I love the diagrams I knew for sure I was ordering the right part.

Easy on Kenmore Performa Dryer, order the High Limit Kit, it got here in 3 days. Unplug from wall, use flathead screwdriver to pop up the top; then look for the High Limit just behind the drum and the smaller fuse below that one on the right. Best to have smaller hexagon ratchet, and be careful not to drop them behind the drum. When you undo the high limit, use needle nose pliers to pull of the contacts from it. Then just attach as you disconnected, be sure you know which was which. Then remove the old smaller one, it can be tricky, and install new one. Then just close up the top, plug it in and it should start right up. Have replaced this every few years, easy and affordable.

I unplugged dryer and removed front of lower dryer unit. Used flashlight and inspected. I found belt and pulley were broken. Using a pair of channel locks I removed the broken pulley. (Pulley has a left hand thread, so I turned it clockwise to remove it. I checked this website and found the parts. The pulley has been redesigned and looked different. I ordered the parts and waited 2 days for the parts to arrive. I turned the pulley onto the threads counter clockwise as hard as I could by hand (don't over tighten this pulley, it will break easily) I slid the belt over the drum and around pulley (making sure the belt was lined up in the same location around drum) and lifted tensioner into place. Instructions come with belt for belt replacement. I re installed front and tested, ok.

quite simply I followed the path that was worn from years of use. it was very apparent the belt had broke. along with the belt there was a generic diagram for proper install. this was very helpful

1.used small flat head screw driver to pop top of dryer. 2.used phillips screw driver to remove front of dryer. 3.disengage dryer belt. 4.take hold of brum and turn and pull out. 5.{left side}take snap ring,washer,roller off then remove support shaft. 6.install new parts, support shaft,roller washer, snap ring. 7,right side has a plastic washer that goes on before roller rest will be as step 5 8.put dryer back together.

took the dryer apart noticed it needed a belt and rear drum supports. Ordered the parts(they were very helpful on getting the right part . they came in very fast (less than 24 hours). replace the broken parts. The dryer is working great.

Opened dryer top, disconnected door wireing, took off front panel, laid dryer on back, cleaned out lint and inside, put new belt on, and put parts back together. Dryer works fine now.

Remove Filter and (2) phillip screws. Use common screw driver to pry top from cabinet. Fold top back. disconnect door switch and removed (2) screws holding front of cabinet and lift frong slightly to remove from cabinet. Remove broken belt and discard. check rollers for freedom and placed drum on rollers. guided belt through idler and around motor pulley. lift front and placed on lower hooks. Lift drum and installed (2) screws that holds front of cabinet to main cabinet. connect door switch and check drum for freedom of turn. turn drum several times to get belt to center. Closed top and replaced (2) screws that hold filter door in place. Install filter and test run dryer. Completed job in about 38 minutes.

I followed the instructions supplied with the belt. I've changed the belt before so was familiar with the repair. The toe panel clips for my model had changed so what was supplied was different than the originals. Although they, too, came with instructions, they did not fit my appliance. They were inexpensive so I scrapped them and used some self-adhesive Velcro fasteners I had in a junk box.

The dryer would not turn on so I checked the power. I then googled the problem and found that the high limit fuse was bad. I ordered the part and simply replaced the fuses after watching the video on the website. Simple and easy. Thanks!