YE20JY4C Magic Chef Dryer - Instructions

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Disconnect the power and gas supply so that you can slide dryer out and into an accessable area to work comfortablely. Removed top and front of dryer. When disconnecting numerous wires from the top controls, draw a simple color coded diagram for reconnection before you disconnect those wires. After removing the top and front, take out the drum and clean all the lint, money etc. out of the normally nonexcessable area of dryer. Place new belt on as you replace the drum. This takes two people; one to hold the drum in position and one to carefully work the new belt into place. Rotating the drum by hand will assist in the placement of the new belt on the drum. After reassembling the newly cleaned dryer it was a pleasure to try it and find a dryer that worked better than during its pre-repair use and it saved us the price of a repair call or a new dryer.

Un pluged and Moved it out from the Wall, Raised the top, found broken belt. ordered belt on line, 2 days belt came in. cleaned all dust and dirt out put greese on berrings for rollers bleu out vent hose with Leef Blower. put top down, pushed back. pluged in and turned on IT WORKS!!!

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

After searching you site for other similar problems, we ordered the part that we thought we needed, it arrived within 3 days, my husband installed the part and the dryer started. The information you have on your site was great, it gives you an idea about what to test before having to call a repairman. There were several people that had the same problem and with their description it was easy to test the fuse. Thanks it saved us alot of money and time. I can't describe how the repair was done, my husband did it, but it was very easy

Popped top open, matched up parts, changed them. Dryer cranked up,got hug from wife. Done life is good.

First, I printed one of these responses which were excellent and very detailed. The screws connecting the lint slot to the top of the dryer was frozen. Taking the front panel off was difficult because I did not read the instructions I printed out very well. After I took the top off I had a hard time finding the 2 screws located inside on the top of the front panel. They are located to the far right and left at the top. To take off the front panel you have to push it up to release the clips on the bottom, then it comes right off. Taking the drum out was easy. What was difficult was putting the belt on. There wasn't any slack and to put it around the pulley and the drum for me was difficult. After that is was a piece of cake. It works great.

First I opened the top of the dryer, then removed the bracket holding the high limit thermostat. Then I removed the heating element to gain access to the thermal fuse. Installation was the reverse. I also cleaned out the lint trap on the front of the dryer and also checked the vent duct (it is cleaned every year). Very easy repair.

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

- Unplug the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.

Pry the front of the top up - it's held on with barbed fasteners that just snap out. Underneath the hood against the back panel is the heating coil assembly. On top of it is the thermostat, hanging from the side of it is the thermal fuse. I removed the heating elements (coiled wires held in frame) to make access to the other parts easier.
Pretty much plug-n-play. One nut driver takes off everything, you might need a needle-nosed pliers to push the lugs onto the contacts of the replacement parts (they fit VERY snugly).

Also, remove the front panel and clean out the lint in the air duct - lint collecting there is apparently what drives up the temp causing the fuse to blow in the first place.

Disconnected power....lifted the top of the dryer to gain access to parts requiring replacement... Unsrcewed two screws 1/4 inch nutdriver....disconnected the two wires...connected the wires to the new part and attached screws...Removed 1 screw from heat element and raised element to get to heat sensor...sensor pops out removed wires and popped new sensor in...replaced wires closed top lid reconnected power source and started dryer

Unplugged dryer.
Popped the lid using a butter knife by pushing in the two latches (located about 4 inches in from the side in the seam where the top lid and front panel meet).
Used pliers to remove the electrical leads to the two fuses (two leads each fuse).
Unscrewed the top fuse from the mounting bracket, then removed the heating coil, then unscrewed the lower/bottom fuse from its mounting bracket. Tested each fuse with my trusty (and rarely used) volt/ohm meter -- which verified that I had bad fuses.
Replaced the bottom/lower fuse, re-attached to the mounting bracket, reconnected the electrical leads.
Replaced the heating coil.
Replaced the top fuse in its mounting bracket and reconnected the electrical leads.
Closed the lid. Plugged in the dryer. Works like a charm.
NOTE: I checked more than 50 feet of exhaust duct to make certain there were no clogs (which is what caused the problem). I discovered that my conduit (that tube-like thing that connects the exhaust from the dryer to the exhaust port in the wall or floor) was kinked and created a clog. I trimmed it and now it works and I have improved drying performance.

i pop the top of the dryer lose and removed the 2 screws that held the front on and installed the new belt and put it back to gethere

First i unplugged the dryer from the outlet. Then I used a flat head screwdriver to lift open the top cover of the dryer. I removed the two wires connected to the thermal fuse and removed the two screws that attached the fuse to the holder. I placed the new fuse on the holder using the two screws. I plugged the two wires back up to the fuse and closed the lid. Be sure to fixed what caused the problem before attempting to use the dryer. I my case there was a massive amount of lint beneath the lint tray which had the vent blocked.