Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!
P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.
I ordered this part to replace broken lint filter. Shipping estimate was 3-5 working days. I had the part 2 days after I ordered it!! I was very surprised and extremely pleased. If I need anymore appliance parts, I know exactly where to go!
noise, shaking, from foreign object in the blower, from operating without the lint filter
Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower. Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.
I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
After searching you site for other similar problems, we ordered the part that we thought we needed, it arrived within 3 days, my husband installed the part and the dryer started. The information you have on your site was great, it gives you an idea about what to test before having to call a repairman. There were several people that had the same problem and with their description it was easy to test the fuse. Thanks it saved us alot of money and time. I can't describe how the repair was done, my husband did it, but it was very easy
After removing the control panel face plate, the lid, the front panel, and the drum, I had to trouble shoot the wiring to determine the dead spot. I found it to be the thermal fuse for the heating element. I then unplugged the wires to the fuse, removed the fuse from the fuse bracket, and then replaced evrything in reverse order.
Unplugged dryer. Popped the lid using a butter knife by pushing in the two latches (located about 4 inches in from the side in the seam where the top lid and front panel meet). Used pliers to remove the electrical leads to the two fuses (two leads each fuse). Unscrewed the top fuse from the mounting bracket, then removed the heating coil, then unscrewed the lower/bottom fuse from its mounting bracket. Tested each fuse with my trusty (and rarely used) volt/ohm meter -- which verified that I had bad fuses. Replaced the bottom/lower fuse, re-attached to the mounting bracket, reconnected the electrical leads. Replaced the heating coil. Replaced the top fuse in its mounting bracket and reconnected the electrical leads. Closed the lid. Plugged in the dryer. Works like a charm. NOTE: I checked more than 50 feet of exhaust duct to make certain there were no clogs (which is what caused the problem). I discovered that my conduit (that tube-like thing that connects the exhaust from the dryer to the exhaust port in the wall or floor) was kinked and created a clog. I trimmed it and now it works and I have improved drying performance.
First I opened the top of the dryer, then removed the bracket holding the high limit thermostat. Then I removed the heating element to gain access to the thermal fuse. Installation was the reverse. I also cleaned out the lint trap on the front of the dryer and also checked the vent duct (it is cleaned every year). Very easy repair.
After reading some tips on the parts select site I isolated the high limit fuse and thermostat as the likely problem. The overheating was caused by a buildup of lint in the exhaust fan area. after clearing the obstruction, and replacing the fuse and switch I tested the dryer which worked perfectly.
High Limit fuse thermostat blew, dryer quit working.
I ordered the part. This is now my third order. It appears that every 10-12 months this happens. I opened the top of the dryer by using a flat head screw driver to push in two clips. The clips are along the front edge of the lid about two inches in from each side. Push in with the screw driver while pulling up the lid. Once the lid is open (of course the plug is pulled) I locate the heat coil. Above the heat coil is the the thermostat, I replace that. Or maybe it is the over heat fuse, I forget. I then replace the sensor found along the side of the heat coil. Re-attach wires. Close lid. Plug back in and ready to go.
Disconnected power....lifted the top of the dryer to gain access to parts requiring replacement... Unsrcewed two screws 1/4 inch nutdriver....disconnected the two wires...connected the wires to the new part and attached screws...Removed 1 screw from heat element and raised element to get to heat sensor...sensor pops out removed wires and popped new sensor in...replaced wires closed top lid reconnected power source and started dryer
