Models > YE209KA

YE209KA Magic Chef Dryer - Overview

Get Parts and Repair Help for YE209KA

If you know the dryer repair part you need, you can browse the list of all parts on the YE209KA, or you can search by name or part description. You can also find your part by where it is located on the YE209KA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YE209KA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.08

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$60.79

Heating Element Kit - 240V 4750W

This kit comes with a high limit thermostat of L248-80.

$37.91

Rear Drum Support Roller Kit

Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts. *** Note: Per manufacturer thi...

$2.70

Blower Wheel Clamp

$2.70

Screw

This screw is sold individually.

$2.70

SCREW

This screw is sold individually.

$19.16

Thermal Fuse

$31.58

Front Drum Support Roller Replacement Kit

This front drum support roller kit is used for many gas and electric clothes dryers. Included in this kit are one right side glide, one left side glide, two adhesive felt pads, a metallic cylinder support brace, and an instructions sheet. Each of the glides are blue in color and are made of a hard plastic. The cylinder support brace is the longest piece in this kit measuring nine inches.

$12.57

Drum Glide and Cushion Kit

Pad has adhesive backing.

$39.45

Blower Wheel - B/10 Models

This blower wheel is suitable for some clothes dryers of the 10 and earlier series. Manufactured to fit a 1/2 inch motor shaft, this blower wheel is 3-1/8 inches deep. The diameter of the wheel is 7-1/8 inches, and the spring clamp is not included.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dry stopped heating - still had good air flow

  • Customer: Brianna from Littleton CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 87 of 105 people found this instruction helpful
I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to fix it. After a little web research, I saw several do-it -yourself stories indicating this was a very easy repair.

This was an extremely easy repair and it save me lots of $$:
(1) Disconnected power
(2) Opened the top of the dryer
read more

broken tumbler belt

  • Customer: Michael from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 73 of 74 people found this instruction helpful
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses suppor... read more

Dryer would not run

  • Customer: Ron from Rutherfordton NC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 37 of 38 people found this instruction helpful
Unplugged unit, lifted the top cover, removed heater element screw, lifted out element, lifted out thermal fuse bracket. Removed wires from thermal fuse, confirmed was open curcuit at room temperature. Attached wires to thermal fuse, inserted fuse into bracket, slid bracket onto clip on side of box that housed the heater element, reinstalled heater elememt... read more