X8261RV Maytag Cooktop - Instructions

USED CHANNELOCK PLIERS TO ROTATE BURNER COUNTER-CLOCKWISE. PULLED OFF THE CONNECTORS, APPLIED RUST TREATMENT TO THE REPLACEMENT PART, WHICH HAD ITSELF STARTED TO CORRODE. SPADE LUGS ON THE OLD PART HAD A SPADE ADAPTER, BUT THE CONNECTION SEEMED TO WORK REGARDLESS OF THE MISS-MATCH. PART WAS REPLACED, TURNING THE BURNER CLOCK-WISE. VERY QUICK AND EASY REPAIR.

Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.

replace burner-had to hit old burn with rubber mallet to break off grease and took old burner off-two wires were connected to it..put those on new burner and was done--have a little problem--flame is lower now than it was-but it turns on

Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.

1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.

just put it in place.

your company was used beacuse they had the part.
delivery was prompt.

Pull off the old one and put on new ones.

Our handyman took off the burner caps and checked after we reported smelling gas. We ordered the replacements here, and they arrived by only the 2nd business day, instead of 3-5 as expected. The only hard part was scouring off the rust, with SOS pads, from the stove top before putting on the new burner caps (a simple plug-in)!! This is very important to check on your stove; you could blow-up your house! The gas was escaping under the old burner cap, through the rusted-out portions.

Your site was easy to navigate, which made determining the problem from other customers easy, and choosing the correct part to replace the malfunctioning burner.

The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.

Replaced the ignition module with one from PartSelect. took care of the problem. They had the part in stock. Great service. Got the part in four days.

I used the advise given in the website and it was very informative- the part was exactly where the folks on the website said it would be and although it wasnt the actual maytag part it was easily fitted by using the wire splices i mentioned and it was shipped quickly The whole process took less the 30 min once received. thank you for a very useful site.

Removed stove top to work bench'
Disassembled burners from enclosure to gain
access to spark module.
removed old module and disconnected slip on electrical connections
Installed four new slipon connectors to match new modual
attached newmodule to frame and connected wires.
Tested unit by pluging into electeic outlet and turning burner dial to lite . Success
reassembled stove top and installed in kitchen.
job complete

Removed screws from back right of oven. Found spark module under right side panel of oven. Module connected in a slightly different way, so I had to drill a new hole and use a machine screw to secure it. All wires matched up exactly on new spark module. Replaced side panel, plugged it in and... SPARKS. Cheap and easy replacement and didn't have to call Maytag for repair!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the six wires. Then I repeated those steps in back order. That's it

I removed the old burner with pliers took off the electrodes. Replace the new burner attach the electrodes placed it back in the burner slot and now it works.