WWXR4100T8AA General Electric Washer - Instructions

There are many on-line videos to help you do this. It's so easy, even a beginner handyperson can do it. For this model, just run a strap under the agitator to assist you in lifting it up off the coupler (good tug). Remove the old worn coupler, put the new one on, set the agitator back on by giving it a little downward push.

Just took the old knob off and put the new knob on. It was a snap. Thanks you very much

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

put the new knob on and pushed it inward !! simple repair..PartSelect is a great company to do business with and very quick shipping, and great prices too. thank you so much.Brad S.

Pushed new knob on starter shaft.

Pulled off agitator with little effort. One 7/16 bolt to remove and the coupler came right off. Pushed on new coupler, replaced with new provided bolt, pushed agitator back on and was back in business!! Very simple inexpensive repair. Thanks Partsselect for your quick parts turnaround!

The motor assembly (630 in the parts diagram) has a spring pin in the drive shaft to connect the drive shaft to the clutch. The spring pin had shattered. Instead of replacing the entire motor assembly ($365), I ordered a new clip from PartSelect, and a new spring pin from McMaster-Carr. Used a screwdriver and mallet to drive out the old spring pin and install the new one. Reinstalled the clutch and clip and everything was good to go.

took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....

Unplugged the unit. Removed water hoses. Removed 4 "star" screws to open control unit cover. Unscrewed assembly with philips screw driver. Unpluged electric plugs. Used pliers to remove internal hose. Removed bad unit which was plugged with hard water corrison. Reverse steps to reinstall. It worked great. Loved the online ordering and shipping direct to my home.

Unplug power. Pull up firmly and quickly from the base of the agitator. Some videos used a rope and 2x4, I didn't have to. The agitator just pops right off. Then with a 7/16" wrench unscrew the bolt while holding on to the coupling. Take agitator coupling off. Clean off metal grooves that the coupling goes on, use either a small screwdriver, metal brush, a knowl, just to make sure you will have good connection with the new coupling. Then install the coupling, new nut, tighten nut firmly. Install agitator pushing down firmly on opposite sides until snaps in place. Turn agitator by hand, it should not free spin. Plug power back in, run washer with water and bleach only in the smallest setting and let it run through its cycle. This will take care of any black debris that might have got into the bowl while fixing. GOOD LUCK!! I also used videos found on Google.

The washing machine was a making a very loud noise when it got to the end of agitation and though it did complete the cycyle it was beginning to snag clothes under the agitator....don't know how. Found that the agitator coupler was cracked in 4 places. Washer is only a year and a half. 4 family washing..so I wanted this fixed quick. The part came super quick..like two days and I was not expecting it for 4 - 10 days...so great and it was cheaper than other places I checked even with paying shipping! I watched the video of installing the coupler--very helpful! I removed the agitator, then removed the agitator coupler....this was already done before the part arrived. When the new coupler arrived, I just had to drop it down onto the spline...there are grooves it must fit to...then I applied the hold down bolt. I used my wrachet/socket to tighten it, but you can use an adjustable wrench. I'm short so reaching down into the washer bowl to get to tighten the bolt was a little ackward..should have used a stool. The loud sound the washer was making before replacing the part stopped and I am back in business...doing ugly washing....LOL! One thing I will mention....nothing to do with the part...but I had without thinking placed the agitator back into the washer bowl....WITHOUT bolting it down..then put the agitator on top of the old coupler. So this made it lock in place under the agitator. My agitator does not have an opening at the top after removing the dust cap inside so there was no way to knock the coupler down and out from the top by putting a long wrench or something down through the top of the agitator(the video shows how to do this also)...sooo....because the agitator coupler locks in place behind moveable clips, I took eight butter knives and wedged them behind each clip on the underside of the coupler pushing each back and was then was able to separate the agitator coupler from the agitator by pulling it forward with my fingers...so don't test putting the agitator over the coupler without first bolting it down! This is all a lot to say about such a small part but this small part is crucial to being able to complete a wash..an ugly wash that is...haha!

I used a pair of pliers to turn my dryer on until I broke the center part where the knob went. I order the part that was in the dryer first and it came the next day. When it got here I realized I still needed the knob. It came the next day also. It took my handyman about 15 minutes to replace both and he also cleaned out all of the missing socks and other items behind my dryer. Good Job!

I had no intention of trying to fix the washer myself after reading about how to do it, only because I didn't know what half of the words were referring to. But once I watched the video, and I saw that the part was going to cost less than $15.00 (shipping included), I thought I would at least try it before going out and buying a new machine. The washer in the video was slightly different than mine, but I recognized the parts from my machine and mine was actually easier to replace than the one in the video. I just pulled off the agitator, unbolted the old agitator coupling and replace it with the new one, bolted it back on and lined up the agitator grooves with coupling and that was it. It worked and saved me a lot of money. I once had an appliance repairman tell me that if your washer or dryer lasts 7 years nowadays, you should consider yourself lucky. Mine is 7 years old, so I thought I would have to replace it. I didn't particularly want to pay someone $100.00 to come to my house and tell me it couldn't be fixed if I was going to have to buy a new one. But fixing it myself was very easy. Written instructions never would have worked for me, but the video was very helpful. Thanks!

I noticed the agitator would spin all the way around, in each direction. Also, the machine would make no sound, associated with washing, during that part of the cycle. I pulled the fabric softener reservoir off, with fingers on each side of the agitator, i pulled straight up and that gives you access to the coupling. Use a 7/16'" socket to loosen the nut, remove it and pull the coupling off. Press the new coupling on the splined shaft, tighten nut, and line up agitator with the grooves, push it down and replace fabric reservoir. Straightforward repair.

Took off old agitator, removed coupling that was bad and put new one on.