WWXR4100T6WW General Electric Washer - Instructions

I just popped in the new agitator. The coupler wasn't needed but I will keep it just in case.

I removed the agitator, replaced the agitator coupling. The guy at the appliance store where I was able to find the part said to check the splines on the inside of the agitator as well. Glad I did, the splines on the agitator were worn out too. So by checking both, if and when the problem occurs, REPLACE BOTH parts! This will save a lot of grief for you!

Was very easy to remove and replace. The instructional video let me know what to expect

Unit unplugged. Next day delivery, saved plastic clip and two screws from hose connect to washer , removed leaking hose ,replaced with new hose fully pushed into unit with plastic clip already in place on new hose. Tightened screws on plastic holding clip on new hose. Done complete job in 5 minutes.

simply replaced knob, it took less than 15 seconds, thank you.

There are many on-line videos to help you do this. It's so easy, even a beginner handyperson can do it. For this model, just run a strap under the agitator to assist you in lifting it up off the coupler (good tug). Remove the old worn coupler, put the new one on, set the agitator back on by giving it a little downward push.

Just took the old knob off and put the new knob on. It was a snap. Thanks you very much

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

put the new knob on and pushed it inward !! simple repair..PartSelect is a great company to do business with and very quick shipping, and great prices too. thank you so much.Brad S.

Belt had worn and was shredding and melting due to pump not draining tub. Too bad my wife and daughters couldn't tell me the pump wasn't working right any sooner. The belts slow disintigration over time made a black, gooey mess inside the machine. Worked on the machine in place and only removed front. Old belt removal was easy with screwdriver prying around motor pulley but replacement was challenging in the tight space under the machine. It did go on by working-rotating belt around back of agitator pulley. By far the hardest part of the job. Replacing pump was easy enough but made a water mess and had to adjust clamps for leaks. Machine is now good to go.

Tried using 5 minute epoxy to glue gear portion back to knob portion first. That didn't work so I ordered a new one. Piece of cake to install!! Not even 1 minute....

As directed by the book.

I opened the box which contained the new selector knob. Placed it on my dryer and immediately turned the knob to start the dryer. Easy steps to follow the video supplied when i ordered the part. I am greatful you responded to my order within 3 days. Thanks

pulled the clip 1/2 way out inserted knob and it snapped into place.

Once I watched the video to replace the pump(Thanks so much for that - big help!!), I disabled the machine to replace the pump, to my surprise found a big clump of fuzzy stuff that was blocking the pump, once I removed that and re-assemble the washer, it started working fine!. Unfortunately, I had already bought the the pump and agitator bell thinking they where both bad, so I'm in the process of returning them now, thanks a bunch! btw - what took so long was I had a mess with the water left in the washer, tip - get all the water out first ;-)