Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WWX645RBS2 > Parts

WWX645RBS2 Frigidaire Washer - Parts

All parts for the Frigidaire Washer WWX645RBS2

Below is a list of all parts for the Frigidaire Washer WWX645RBS2. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the WWX645RBS2
1-14 of 134
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$5.42

Screw-In Plastic Leveling Leg

Sold individually.

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

$9.33

Tension Idler Pulley

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operating, you might need to replace the tension idler pulley. The tension idler pulley works in conjunction with the drive belt, so you might need to replace the belt as well as the pulley. Once the old pulley has been removed from the washer, you will need to transfer the spring and bushing from the old pulley to the new one before re-attaching it to the washer.

$48.20

Tub Seal Assembly

If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of th...

$6.55

SCREW

Sold individually.

$6.23

SCREW

$22.37

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you may need to replace the snubber ring. Because the snubber ring is located under the tub of the washing machine, you will need to remove the front panel to access it. To protect your hands when removing the snubber ring, consider using a bent coat hanger or a sturdy wire with a hook to pull the old snubber ring free. Be sure to disconnect the power and water sources for the washing machine before you begin this repair.

$30.42

Agitator Drive Block

The agitator drive block rotates the agitator assembly in your washer. If the drive block breaks down due to wear and tear the agitator will stop working. If you notice that your w...

$9.26

CLAMP

Clamp used for hoses.

$29.13

Tension Spring

This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the ten...

$8.47

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

$8.76

SPACER

This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery ...

$48.78

Spin Bearing

The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, therefore ensuring the shaft is spun properly during its spin cycle. If your spin cycle makes loud or odd noises, replacing the bearing could be a solution to your problem. Refer to the diagram provided by the manufacturer for further installation instructions. As a safety precaution make sure to unplug appliance from the power source.

All Parts for the WWX645RBS2
1-14 of 134