Models > WWSE3160A0AA > Instructions

WWSE3160A0AA General Electric Washer - Instructions

All Instructions for the WWSE3160A0AA
481 - 490 of 490
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer agitator wouldn't agitate
remove the agitator by just pulling it up, remove the bolt that hold the agitator coupling down and install the new one.
Parts Used:
Agitator Coupling Kit
  • Jose from Pulaski, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator Would Not Move
Found that the teeth and the agitator coupler hade stripped out. Replaced the coupling and everything worked great. 10 Min and $10. 00 Fixed it up.
Parts Used:
Agitator Coupling Kit
  • TIMOTHY from KANSAS CITY, KS
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Plastics broke on inside of "Start" knob
Pushed new knob on starter shaft.
Parts Used:
Selector Knob with Clip
  • Peter from Mercerville, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
wouldnt agitate
Took off old agitator, removed coupling that was bad and put new one on.
Parts Used:
Agitator Coupling Kit
  • Shawna from LaCenter, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer was not agitating
I used the video instructions sent to my email and everything worked perfectly as instructed.
Parts Used:
Agitator Coupling Kit
  • Maud from Ellicott City, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
One of the paddles broke from washing something that wedge in between one of the paddles and side of tub. Which broke the blade. Order the the part from Parts Select. Watched the Video how to change the Agitator. It was as easy as they said. Repaired it myself for least than $50.00.
Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.
Parts Used:
Dual Action Agitator
  • Pamela from Locust Grove, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The Roll pin had shattered destroying the clutch clip
The motor assembly (630 in the parts diagram) has a spring pin in the drive shaft to connect the drive shaft to the clutch. The spring pin had shattered. Instead of replacing the entire motor assembly ($365), I ordered a new clip from PartSelect, and a new spring pin from McMaster-Carr. Used a screwdriver and mallet to drive out the old spring pin and install the new one. Reinstalled the clutch and clip and everything was good to go.
Parts Used:
Retaining Clip for Clutch
  • Alan from SIMI VALLEY, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
Agitator not working, spin cycle ok.
Removed agitator by pulling up, wiggle to and fro, watch out for unexpected release. Agitator coupler was worn, stripped splines. 7\16 socket, long extension to remove bolt in coupler. Install new coupler, new bolt, then line up agitator to splines on agitator coupler and push to snap in place.
Parts Used:
Agitator Coupling Kit Dual Action Agitator
  • Walter from Atlanta, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Stripped plastic coupler spline
Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done
Parts Used:
Agitator Coupling Kit
  • frank from palm city, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The gear agitator had striped. Wouldn't spin the blades to wash the clothes.
I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.
Parts Used:
Agitator Coupling Kit
  • Gerardo from Mountain House, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WWSE3160A0AA
481 - 490 of 490
Back to Top