Models > WWEF3006KWB > Instructions

WWEF3006KWB Westinghouse Range - Instructions

All installation instructions for WWEF3006KWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWEF3006KWB
46-60 of 455
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven element broke

  • Customer: Irving from Germantown MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!

Old heating element broke

  • Customer: Paul from Ellenville NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

Bake element began burning itself up.

  • Customer: Don L from La Grande OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.

Oven lower element broke

  • Customer: Peggy from Owensville MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

Element did not heat

  • Customer: Susan from Iowa City IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 2 of 3 people found this instruction helpful
After doing without the oven for a week or so we decided to turn to the internet and try doing the repair ourselves. We are not mechanically inclined/fix it yourself kind of people. This really was easy. Just detach the old element and attached the new one. A couple of bolts and snapping one out and then the new one in. Very simple

Lower baking element would not heat up.

  • Customer: Jim from Harrison MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim

Bake Element burned in to stopped working

  • Customer: Debbie from Mineral Wells TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

Bottom bake element went bad

  • Customer: James from Martinsburg WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

Oven bake element was dead

  • Customer: Stephen from Spencer IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 2 of 3 people found this instruction helpful
Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.

bake element burnt out

  • Customer: Kim from Union Grove WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

N/A

  • Customer: Dineshbhai from Rincon HWY21 GA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I had open back cover And remove the switch than replace new switch. Makesure cable conection.

Large front burner would not come on under setting of "3"

  • Customer: Steven from Edina MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
Replaced infinite control very easily.

Heat element burned out.

  • Customer: Laura from Hurricane UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
The problem I ran into Was; Having the right socket size for doing the project. After taking care of that problem it was fairly easily to disconnect the element and reconnect the new one. It's pretty self explanitory.

Didn't Bake

  • Customer: Dale from Athens TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Took it off, ordered a new part and put it back on.
Ordered on Monday and got the part on Tuesday.

Oven wouldn't heat

  • Customer: KaShira from Wilmington OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!
All Instructions for the WWEF3006KWB
46-60 of 455