WWEF3004KWG Westinghouse Range - Instructions

Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.

My husband followed the video instructions and it was easy to fix.

Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.

I follow the video on your site

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

Screw the handle, that it...

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!

Removed 8 screws from back, took out timer and replaced. Simple. $112 fix versus replacing with a $600 oven. Good for another 5 years!

Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into back wall of oven. Don't know what you would do then.