WU180 Dishwasher - Instructions

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!

Remove old seal by pulling out tabs one at a time.

To install new seal, I had to remove the front control panel and door panel to access the back side of all of the slots that the new seal tabs go into. Using needlenose pliers i pulled each tab individually until they were locked into place.
Replace door and control panel.

Alighned the bracket and pushed in.

With the dishwasher door open remove the 3 srews connecting the top of the dishwasher to the bottom of the kitchen counter top. Remove the lower access panel from the dishwasher and lower the dishwasher about 1/4 inch in the front and back of the dishwasher). Once you have lowered the dishwasher enough slide the dishwasher out about 6 inches (enough to gain access to the door springs on the left and right side). Remove all broken spring parts and replace using new springs. The left side of the door contained a single heavy duty spring and the right side of the door contained a heavy duty and light duty 'helper' spring. I replaced only the right side springs since the left side spring was in excellent condition. When the springs are installed slide the dishwasher back into its original position and raise the dishwasher back up to its original height using the front and back adjustment screws. Replace the 3 screws holding the top of the dishwasher secure to the bottom of the countertop. Ensure that the door opens, closes and latches smoothly and then replace the lower access panel. Job done.

I attempted to fix it about a year ago. Took apart the screen center stem and water spinner.
I could not find anything wrong. The machine was used very infrequently over the years. Recently my wife approached me again to fix it and knowing I didn't find any thing the first time: I took the lower panel strip off and found the translucent belt broken. I found your site matched up a belt size and ordered it. Three days later it arrived, I installed it and everything seems to work. The water drains and I'm back in business. It was so easy I was embarrassed I did not fix it the first time.

This repair is very simple. Partselect.com sells a repair kit for this problem that you can use but for simplicity the entire unit is not that much more. First remove the four outside lower philips head screws on the inside of your dishwasher door. Support outer door panel while removing screws. This will remove the outer door panel to gain access to the detergent cup. Remove panel by pulling out bottom first then slightly pulling downward. You will then see the detergent cup. Unplug the two leads that are connected to the unit keeping in mind their orientation. Remove the five screws that hold the detergent cup in place. Remove the cup assembly and gasket. Clean gasket area and install new cup and gasket. Reinstall five screws (do not overtighten) and plug leads back in. To reinstall door panel position door panel at a slight angle and install top first sliding upward into place under control panel then push inward at bottom. Reinstall the four philips head screws on the inside and you are finished. The complete repair will take you less than 30 minutes.

I pulled the dishwasher out & watch it complete 1 cycle : water was leaking at a through hole used to secure the upper dish rack roller to the cabinet : the nut & seal holding the roller was loose allowing water to drip down the outside of the cabinet under the insulation.: water dripped onto the belt causing belt to slip : many water marks around the pump ; as a precaution i replaced the pump bottom seal & the pump to chassis gasket : I also checked the other 3 rolles ; replaced cracked top flange & installed a more flexable water supply hose .

Removed the gasket by pulling it's tabs out of the metal slots in the door. This was accomplished by accessing the inside of the door.
Then I realized that I had to dissassemble the side and front panel of the door to install the new gasket. The reason is you have to pull the tabs through the metal slots in the door from the front side. I used needle nose pliers which worked well. Then I had to reassemble the front and sides of the door. No more leaks!! for now. Takes some time if you do it by yourself. Budget at least 2 hours.

I had already loosened the motor from inside the tub....so it was fairly easy to wrap the new belt around the motor/pulley system.... even though the old broken belt was 2 inches longer than the new belt(probably as a result of age and use, but the new belt is obviously the right size!) Once in place, I did have to take some care in screwing down the seal from inside being as it wanted to go more to one side than the other from the pressure of the tight belt, but all in all, it wasn't so bad. Unfortunately for me when I put the dishwasher on, I thought the dirty water problem would go away, but I soon learned that I also had a clog in the plumbing. I guess I'll never know if one thing caused the other or it was just 2 things going wrong at the same exact time. But everything is perfect now. Also, the part I ordered was at my doorstep in less than 36 hours!!!! That's fantastic!

Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers

Removed under-door front panel. Removed broken spring from right side. Hold door half open, insert spring with plastic bearing into hole in door hinge. Pull down to seat bearing in hinge. With needle nose pliers insert spring into hole at base of washer. ( You do not need to pull washer out of position)

remove lower access panel to expose spring. remove broken spring with longnose pliers. with door closed install upper hook of spring with nylon bushing on door hinge. using longnose pliers pull down on spring to hook on lower braket.

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.