WRT8G3EW2 Westinghouse Refrigerator - Instructions

The parts came two days after I ordered, they were the correct part and went in with ease. Couldn't be more happy with service from parts select. Awesome job.

purchased a defrost theromast,took about 20-30 minutes to take apart & put back together.delivery was in one day from the time of my purchase.thanks for all ur help &prompt delivery.

Removed the timer, installed the new one. Great service from part select

It was as easy as pie. We just carefully slid the shelf into place. That was it.

the bottom door shelf bracket had broken in half, i unsnapped the two halves, i ordered the replacment part from part select which had sent the part within the time frame they promised and just snapped the bracket back in place. the whole process took less then two minutes.

Insert new glass into slot. Took less than 2 minutes.

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!

Removed shelf unscrewed screw on both supports replaced and secured.

Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic

place the bottom half of handle on the screw inthe door then placed the other end of handle over the door and screw in to place.

Cleaned the surfaces,installed the new handle...WaLa! Could not have been easier. Plus the new handle arrived in 2-3 days. AND was less than 1/2 the price of ordering through Sears Parts. I would use PartsSelect again in a heartbeat! Thank you for your great customer service.

We ordered a new bracket and it was installed and in in less than 10 minutes.

Popped the new retainer bar into place. Put the jars back where they belong. No worries! Couldn't have been less trouble.

it was easy my wife did it wen i went to the fridge it was already installed. thank you!!!!

Installed Metal hinge(old hinge was plastic) to take out sag of door.(painted the hinge color of refrigerator as hinge doesn't have plastic appearance cover )