WRT771RWYB01 Whirlpool Refrigerator - Instructions

exactly as shown on the video and it was completed in less than 10 minutes with only a nutdriver; took wife to dinner with the money saved and returned to find ice in bin without the "iceberg" from the prior leak! Thanks for the great parts selection, clear description of problems to help select correct fix and most of all the "how-to" video. I'm a customer for life ! WSD

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Had a 1999 Kitchenaid Superba refrigerator that quit making ice. Based on online research, my icemaker's problem could have been either the icemaker itself or the dual water valve. I opted to try the icemaker replacement first after watching the helpful installation video. The only issue I had that made the repair the slightest bit difficult was that bolt-headed screws were used to secure the icemaker to the fridge wall rather than Phillips and the one nearest the door can't be seen while trying to loosen it. It only took an extra ten minutes to overcome this obstacle (maybe 20 minutes total). After replacing the icemaker, I thought the water valve must have been the problem after all since the unit did not immediately start filling with water. However, once the unit chilled down, it worked perfectly.

Loosened 2 screws,un pluged the wiring harness,pluged the new ice maker in,tightened the 2 screws. . And I now have ice!! Very easy to install. .

Found the replacement icemaker I needed on your web site,ordered and recdeived it within 2 days. Watched the how to video and did the replacement in less than 5 minutes.However,I waited(2 days) for the icemaker to start working, it never did. Thinking there was another problem in the icemaking system, I contacted a local appliance repair shop. They checked the entire system and everything was ok except the new icemaker. Turns out the new icemaker was defective. I contacted PartSelect and reported the technicians findings. I had another new icemaker in 2 days again. I again installed the new one and am now making ice. Thank you for the installation video and the teriffic service.

determend o.k. water flow,determend solenoids o.k.problem had to be ice maker.ordered part on Su. eve.,recieved new part Tue.A.M.,had part installed in 15 minutes. Then waited for quite a long time untill it finally made ice.

Per directions supplied

Removed the old one. The new one had a power chord attached but it did not connect to the wire in the freezer. I saw it could be unplugged from the new ice maker and the power chord from the freezer plugged right in. Once installed, was not sure it worked but after a few hours it filled with water and started making ice. Works great now.

I installed the new icemaker that was missing the shutoff arm then I ordered the arm from you and installed it. End of story.

I have a side by side so the space to work in was limited but I still completed the install in about 30 minutes. Unplugged the refrigerator then loosened the top two screws took out the bottom screw lifted the ice maker out just far enough to disconnect the power cord reversed the procedure. plugged it back in started making ice in 30 minutes. Probably would have not have taken that long my MS slowed me down a little. The repair man was going to be $300.00 plus $$75.00 trip charge what I paid was $128.41 that was with 3 day shipping.

unplug frig, didnt turn off water used cord light to see. Took 1/4 nutdriver and loosen screws removed screw on bottom bracket uplugged ice maker. reversed the process for the new one and done

Ordered the part and within 8 minutes I had installed it without having to use any of the included wire harnesses. Was making ice within six hours. If you take your time before, review the handy video PartSelect provides online and prepare the work space it should be a snap. I can't say enough good things about the swift delivery and usefulness of the part. Also, best price I could find after shopping competitors. I highly recommend this project, it was easy and should make using your otherwise working refrigerator more enjoyable.

Watched the 'self-help' video on your website. Loosened the 3 sheetmetal screws,loosened the icemaker, unplugged the single connector and did the reverse order with the new icemaker. Very, very easy.

Removed ice maker held on by 3 screws, took out 2 screws holding back panel, removed 2 screws holding bracket for fan motor, replaced evaporator fan motor and everything works great. Beware of thin splines, I have large hands and bummed up against them and slice one knuckle in 3 places which bleed profusely.