WRT771REYM00 Whirlpool Refrigerator - Instructions

I have a side by side so the space to work in was limited but I still completed the install in about 30 minutes. Unplugged the refrigerator then loosened the top two screws took out the bottom screw lifted the ice maker out just far enough to disconnect the power cord reversed the procedure. plugged it back in started making ice in 30 minutes. Probably would have not have taken that long my MS slowed me down a little. The repair man was going to be $300.00 plus $$75.00 trip charge what I paid was $128.41 that was with 3 day shipping.

unplug frig, didnt turn off water used cord light to see. Took 1/4 nutdriver and loosen screws removed screw on bottom bracket uplugged ice maker. reversed the process for the new one and done

Ordered the part and within 8 minutes I had installed it without having to use any of the included wire harnesses. Was making ice within six hours. If you take your time before, review the handy video PartSelect provides online and prepare the work space it should be a snap. I can't say enough good things about the swift delivery and usefulness of the part. Also, best price I could find after shopping competitors. I highly recommend this project, it was easy and should make using your otherwise working refrigerator more enjoyable.

Watched the 'self-help' video on your website. Loosened the 3 sheetmetal screws,loosened the icemaker, unplugged the single connector and did the reverse order with the new icemaker. Very, very easy.

Removed ice maker held on by 3 screws, took out 2 screws holding back panel, removed 2 screws holding bracket for fan motor, replaced evaporator fan motor and everything works great. Beware of thin splines, I have large hands and bummed up against them and slice one knuckle in 3 places which bleed profusely.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!

unplugged the fridge removed the shelf, remove the rear wall to access the motor removed the 2 screws holding the motor and unplugged motor from harness, then unplugged the groung wire .then put it back together up and running in 15 mins.

I watched the ice maker installation video and I installed the new ice maker with no problem and was done in less the 30 min. with everything. The ice maker is working great. thank you Fred

I receved the new ice maker and the only problem I had was getting the old ice maker plug disconected from the frig.

turned off power unscrewed all the screw that mount ice maker, used flat head to release the clip on the wire harness, took out and exchanged the overfill wire, plugged the new unit in at wire harness, lined up and leveled ice maker tighten all the mounting screws, very simple repair i am very happy that you still had the orginal (OEM) ice maker, thanks Herb

The fridge went warm and I noticed ice build-up on the freezer floor underneath the coils. I mistakenly thought that the defrost heater (or thermostat or timer) must have been the culprit. I used a voltmeter to test those components and chased a wild goose for quite sometime before realizing that the evaporator fan was not spinning and that it failed a test with the voltmeter. Replacing the fan easily fixed my problem! I later realized that the sheet of ice on the freezer floor indicated that the defrost cycle had been working. Were that not the case, the ice would have been all over the coils.

The repair man came out and said the Ice Maker is broken.He said to call him when I get the part but after looking at the video it took 10 minutes to Install. If you can use a screw driver this part is a piece of cake. Oh don't forget to unplug the frig. God Luck John Bronx NY

very easy two small screws, no problems

Opened holder removed old filter and replaced with new filter