WRT18MP6CSI Crosley Refrigerator - Instructions

This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

When cleaning the coils on your refrigerator always remember rule number 1, unplug it first. I was cleaning the coils and hit the fan blade while it was moving with a brush, thus breaking off one of the fan blades. I ordered a new fan and installed it in about 15 minutes. Very easy repair.

pan-crisper pan was easy because is just slide in. the drawer support rail just took a screwdriver to unscrew the screw and replace it with new rail and put the screw back in. The thing I like the best is the fast service of the parts to me.

pulled broke rack off, snapped new one in place. Yeah!! No more broken jars on the floor.

I just snapped the new shelves in place and !voila! I should've done this years ago.

The gasket pops into a channel could not have been easier.

Took whole shelf out. Unscrewed the old rail, screwed in the new rail. Female 55yrs old. I broke it myself and fixed it myself! Very easy!!!!

This was a really easy replacement job, but it did not have any directions. The main thing to know is to really "warm" up the new gasket before installing so that it can easily be fit into the door of the refrigerator. Some recommend putting it in warm water, but it's pretty big & I didn't have anything to put it in, so I used a hairdryer to soften it up. It also takes a few days for it to "form" to the door. When I received it, the top right had a seem split, not an actual "rip" but it looked like the glue did not stay to connect the edges very well. I called and Part Select issued a refund and got a new one out to me the next day! Great company!

Really, really, really easy:
1.Unplug refrigerator (electrical safety).
2.Remove cardboard cover at bottom of refrigerator (two short self-tapping bolts) with a wrench.
3.Pull old fan blade off fan motor shaft (just held on by a compression fitting--no tools needed).
4.Push new fan blade on shaft.
5. Replace cardboard cover.
6. Plug in refrigerator, write nasty letter to Frigidaire.

Simply snap the old ones out and install the new ones. Piece of cake. . . . . And saved some $$$.

removed the screws in the piece of the rail that was still attached and replace with new one - hardest part was the screw it was so little I started it without the magnetic screw driver - it took about 20 minutes

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

No long shelf came with our new refrigerator, Frigdaire did not have one so I went on-line from you and it fit perfectly, now everything does not have to be in one big heap.

Bought a new
capacitor.