Models > WRS6R3EW0 > Instructions

WRS6R3EW0 Westinghouse Refrigerator - Instructions

All installation instructions for WRS6R3EW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WRS6R3EW0
1-15 of 808
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Aged parts broken

  • Customer: Erik from Evans GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 552 of 561 people found this instruction helpful
After sitting in a cold refrigerator for year after year, plastic becomes brittle and breaks. This is what started happening to my shelves and door bins. The problem a lot of times is getting the right part since some of the parts do not have numbers.

This website gives a accurate description and best of all photos on an inch grid, so I can measure what I have and find what I need. This time everything was perfect and fit easily. took no time and just like that I have almost double the space again. Funny how that works. Once before I didn't get the right piece so just pay attention to the dimensions.

Water in Frig was tasting bad.

  • Customer: Patricia from Fulton MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 475 of 475 people found this instruction helpful
I turned the cap for the old filter and pulled it out . Then I put in the new one in and turned the cap to secure it in frig.

cracked, broken door bins

  • Customer: Beverly from Jackso MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 477 of 485 people found this instruction helpful
The new bins and I installed them in the door. Nice to have door space again.

freezer shelf broke

  • Customer: MONICA from LANCASTER CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 472 of 479 people found this instruction helpful
Easy slide it back in place

Shelf cracked because excessive weight put on it

  • Customer: GEORGE from GARDEN GROVE CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 444 of 524 people found this instruction helpful
Slip the old one off and replace the new one with just snapping it in place!

water from refigerator dispenser started tasting bad

  • Customer: Anthony from Springfield VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 345 of 346 people found this instruction helpful
I removed the top shelf in the fridge. I then unscrewed the cover to the water filter and pulled the filter cartridge down into the cover. Keep the cover upright as there may be some water in it. I carried it to the sink. I took the new cartridge and ran water through it from the sink, then set it in the cover and took it to the fridge. I pushed the cartridge up into the space that I removed the old one from and screwed the cover back on. Then I took an empty pitcher and filled it from the water dispenser in the fridge door. I did this three times to charge the filter and remove charcoal dust. Water tastes great now. I ordered two filters so I would ony have to buy once a year. Great site to order the filters from. Cheaper than other sources and delivery was quick.

water leaking out of refrigerator

  • Customer: Jose from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 248 of 296 people found this instruction helpful
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 190 of 195 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 170 of 210 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and note which pipe you unclipped it from. Cut the wires on the old thermostat midway between the plugs and the sensor. Using the supplied butt connectors, strip the wire ends on color matched wires (should be a dark blue or black) and crimp them together. Repeat with the other wire. Discard the white shrink wrapping. I wasn't able to get it small enough with a hair dryer or lighter. Plug the thermostat back into it's respective plugs. Clip the thermostat back onto the pipe you removed it from. Replace the back panel with the four screws. Ensure the bottom of the panel is set inside of the drip tray. Replace any shelving you removed. Plug the refrigerator back into the wall. Your done!

icemaker stopped making ice

  • Customer: David from New Bern NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 156 of 186 people found this instruction helpful
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.

Needed to replace water filter

  • Customer: Karen from Lowell NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 149 of 169 people found this instruction helpful
It was really easy. All you have to do is twist the old filter out, stick in the new one and twist!

had broken sheves on the doors and the crisper drawers weren't suported

  • Customer: Fred from Plano TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 182 of 337 people found this instruction helpful
The only difficult aspect of the job was getting the old shelf support stud removed from the refrigerator wall - the support was broken off too short to allow vise grips to hold it. I had to use two screwdrivers to get under and then pop out the stud to the point I could get the pliers to hold. Everything eles pretty much just "fell together" very easily.

broke two door bins, one on frig and one on freezer doors

  • Customer: Linda from Tierra Verde FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 128 of 200 people found this instruction helpful
We had the bins the next day. I had called some other companies and they wanted twice your price! You were much more curteous on the phone, much more professional and quicker and cheaper! I will tell everyone in Florida who to call if they need a part!
Thank you so much!
Linda Cecil

Old refrigerator shelves broke.

  • Customer: Jorge from Roswell GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 85 of 87 people found this instruction helpful
Replaced with new parts... they just pop right in. Cheap plastic used by manufacturer gets brittle with exposure to low temperatures and over a mere 5 years all break off. Very annoying.

ICE MAKER STOPPED WORKING

  • Customer: JACK from MESA AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 84 of 90 people found this instruction helpful
IT WAS PRETTY STRAIGHT FORWARD. REMOVE THE TWO SCREWS THAT HOLD THE UNIT TO THE WALL OF THE FREEZER. IN MY CASE, I HAD TO USE A DIFFERENT ICE MAKER THAN WHAT CAME WITH THE FRIG. IN ORDER TO INSTALL THE REPLACEMENT UNIT THEY SENT A WIRE ADAPTOR SO IT WOULD ATTACH TO THE EXISTING WIRING. THAT TOO WAS ALL FINE AND DANDY. THE ONLY PROBLEM WAS THAT THE END OF THE WIRE ADAPTOR DID NOT FIT THROUGH THE EXISTING HOLE IN THE REAR OF THE FRIG. I USED A UTILITY KNIFE TO CUT THROUGH THE THIN METAL LINING. THAT WORKED JUST FINE. HOWEVER, I COULD NOT CUT THROUGH THE INSULATION BECAUSE I COULD NOT REACH IT THROUGH THE SMALL HOLE. THE EXCESS WIRE WAS SUPPOSED TO BE PULLED THROUGH THE HOLE AND OUT THROUGH THE BACK OF THE UNIT. SO NOW THE EXCESS IS BETWEEN THE WALL OF THE FREEZER AND THE INSULATION.
THE UNIT IS WORKING WONDERFULLY. IN FACT, IT IS MAKING MORE ICE THAN I CAN USE. I AM VERY PLEASED WITH THE REPLACEMENT UNIT. THIS IS THE 3RD ICE MAKER THAT HAS BEEN IN THIS FRIG. ALL THE OTHERS HAD A DESIGN FLAW THAT HAD A LEAK IN THE REAR OF THE UNIT. THIS CAUSED ALL THE ICE TO FORM INTO A BIG BLOCK. THE REPLACEMENT UNIT HAS NOT HAD THIS PROBLEM SO FAR.
THANK YOU FOR ALLOWING ME TO EXPLAIN MY SITUATION SO THAT MAYBE OTHERS MAY BENIFIT FROM MY EXPERIENCE.
THANK YOU.

JACK
All Instructions for the WRS6R3EW0
1-15 of 808