WRS3R3EW6 Westinghouse Refrigerator - Instructions

Took out the old one and pushed in the new one. Easy, peasy.

Remove the water tray. Remove 3 screws at bottom of cover with Phillips screwdriver. Slid frame upward, disconnect wires from door. Remove screws that held the water actuator. Took broken water actuator out, slid new one in. Screw in place. put parts back in place and bingo, all done. Easy!!!

I followed the instructions provided in the Part Select video and replaced the bearing. The most time consuming part of the job was emptying (and then cleaning) the items stored in the bins inside the door shelves. Removing the broken bearing was a little more difficult because mine was old and broken and I didn't have an empty table to lay the door on like the video studio did--the floor worked in place of the table.

I removed the food on the door and placed it in the refrigerator. I placed a plastic sheet over the opening of the refrigerator to keep the cold air in. Then I removed the bracket for the upper hinge, remover the door and placed it onto a table. Then I removed the plastic bearing from the bottom of door. I then replaced it with the new bearing. Then I removed the lower bearing and its bracket from the refrigerator. At this point I had to modify the new lower bracket by removing the alignment tab with a dremel because there wasn’t any hole in the housing for it. Then I attached the new bracket and bearing. Replaced the door and upper hinge and the job was complete. It took only about a half an hour to finish.

I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

It was easy. Watched the short video and placed the part right in. The part came a lot fasted then we thought. Thank you partselect.

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

Followed instructions on video from Instance Repairman. Very easy to follow directions. He does step by step instructions.

We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle

Snap out and snap in.

after watching the video I followed to the tee used the screw driver tapped out the old peg and removed the stem in minutes I was tapping in the new parts

The repair was easy. After looking at the diagram and locating the part need i just ordered it. But I wish I had taken the door off before ordering as I really need a second part. So resulting in extra shipping cost. Parts that were needed were 240328201 and 240457702. Tks Jim

If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.

These bins just snapped into place. very easy.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.