Models > WRS26MR4JS8 > Instructions

WRS26MR4JS8 Crosley Refrigerator - Instructions

All Instructions for the WRS26MR4JS8
586 - 600 of 759
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
ice maker was not making ice, no water flow into.
watched the youtube video from PartsSelect and was able to remove old water inlet valve easily and install new one with little effort. The hoses on my refrigerator were a bit different than shown in video, but I was able to modify them and it's working just fine now. Thank you PartsSelect !
Parts Used:
Refrigerator Water Inlet Valve
  • Mary from Mt Pleasant, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
When I opened the door, sometimes the light was not turned on.
With the help of a knife we took out the light switch unplugged it, plugged in the new one and it started working.
Parts Used:
Light Switch
  • Helen from Burnsville, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Original Seal was broken
Pulled out the old seal by hand. Cleaned the opening. Pressed the new seal in place. The entire process took about five minutes
Parts Used:
Fresh Food Door Gasket - Black
  • Thomas from Saranac, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bottom bin on refrigerator door was cracked, and fell off.
The new bin I ordered was delivered in one day.I was very impressed. The part just slid right on the door.No tools. Very easy. I'm very pleased.
Parts Used:
Refrigerator Door Bin
  • Camille M. from Branford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the drive blade for ice maker was rusted
first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .
Parts Used:
DRIVE BLADE
  • Michael from Philadelphia, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The ice maker quit producing ie
Purchased a new ice maker assembly and installed. Very easy
Parts Used:
Refrigerator Ice Maker Assembly
  • Tommie from Port Lavaca, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken shelves
Easy to install (self explanitory)
Parts Used:
Crisper Cover Support - Front Crisper Support - Rear
  • Pamela from Brooklyn, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Upper Crisper Pan was cracked
I replaced broken tray with new one.
Parts Used:
Refrigerator Crisper Drawer
  • Michael from Bethlehem, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Botton door bin was broken.
Simple replacement. Fit perfectly.
Parts Used:
Refrigerator Door Bin
  • DEBRA from EDMOND, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
frost build up in side on the back of the freezer .and my my filter housing cup crack due to ice build up inside .freezer side not to cold and fridge side to cold freezer and fridge side to factory settings
before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you
Parts Used:
Defrost Thermostat Kit
  • Carlos from Newton, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
refrigerator ice maker was not making ice, water on floor
used videos and followed instructions to repair. The water inlet valve was first changed because no ice was being made. Changed ice maker due to no cycle and no sound came from it. The water filter was then changed due to length of time since last changed. Plugged up refrigerator and turned water back on and within 2 hours we had ice again.
Parts Used:
Refrigerator Water Inlet Valve Refrigerator Ice Maker Assembly Water Filter
  • Richard from Rogersville, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
the ice auger, and ice crusher broke
Just slide out the old part, slide in the new one, took less than 10 min
Parts Used:
Ice Container and Auger Assembly
  • Charles from Splendora, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
When the ice maker was filling the ice tray with water, the water would come out the water dispenser at the same time.
First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.
Parts Used:
Refrigerator Water Inlet Valve
  • Greg from Murrieta, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Wiring harness too thick to fit where the instructions told me to put it.
After trying several times to fit the wiring harness beside the ice maker without any success, I folded the wiring harness behind the ice maker. Between it and the back of the freezer.
Parts Used:
Ice Container and Auger Assembly
  • SHARON from Lynchburg, VA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Missing door shelves and bins required replacement for my refrigerator
The replacement pieces for my refrigerator were easy to install and took about 3 mins to attach 3 shelves and 1 bin.
Parts Used:
Door Shelf Refrigerator Door Bin
  • Pamela from LAWRENCEVILLE, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WRS26MR4JS8
586 - 600 of 759
Back to Top