WRS26MF5AW3 Westinghouse Refrigerator - Instructions

First I remove the water catch tray. Then I removed the three screws the hold the face plate on. ( You do have to slide face plate upward) I let that hang gently. Then I removed the three screws that hold the mother board in place, tilt the motherboard out to be able to see the back of the actuator. Remove three screws and flanges that hold actuator in place. Look at how spring is held in place before removing. Remove actuator, replace with new actuator set spring, replace screws and flanges, push motherboard back in place,replace the three screws,replace face plate with the three screws and replace catch tray. And your done!!!!

Took out the support and put back in the new one.

turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

replaced water filter per instruction manual.

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

Fridge came ice maker assy configured with an ice cream shelf to maximize space. I found this annoying becuase it blocked access to the ice maker controls and ice bin, which is useful for bulk access even thought there's a door front dispenser for ice. I recognized parts diagrams for a similar model and corrctly assumed they'd fit. So for $30 and an easy change I have the feature I wanted. Pretty cool.

My repair was a simple as logging on to the "PartSelect.com" website - very easy to find the specific part I needed. The website makes the part selection a breeze.

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

easy. Just slipped it in

it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks

Took out two screws, installed new parts, put screws back in. Done.

Removed the door,pried out broken pieces.Replaced with new bearing{bushing}Lubricated bearing with light grease and replaced door.Took about 15 minutes by myself.

I can fix just about anything, but when I'm approaching to fix an item that I have previously no experience with I always do some research before attempting a repair. Once I diagnosed the problem (The evaporator fan was not kicking on), I purchased both the thermostat and fan because either one of them could be the source as to why the refrigerator was not working. Unless you want to drink room temperature milk for three to four more days, I highly recommend that you replace both. After cleaning out the freezer and removing the pull out bucket, I removed the screws and pulled out the metal enclosure. The fan was easy to take out along with the thermostat. The time consuming part of the repair was splicing the old wiring harness with the new thermostat and condenser fan since the replacement condenser fan had a different wiring harness. I had to heat sink the butt splice connectors and I wrapped all the wires in a cold weather electric tape. After that I plugged the refrigerator right in and to my delight it worked :) I love this website because it is very user friendly accompanied with fast and efficient shipping. Thanks again!

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

Very easy repair. Remove 2 screws, unplug wire harness. My model used the included harness adapter. I needed to secure the extra harness length with the included cable ties. Icemaker went back in smoothly with no problems. Making ice like crazy now.