Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS23MF5ASH > Parts

WRS23MF5ASH Westinghouse Refrigerator - Parts

All parts for the Westinghouse Refrigerator WRS23MF5ASH

Below is a list of all parts for the Westinghouse Refrigerator WRS23MF5ASH - White. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the WRS23MF5ASH
1-14 of 292
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.76

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

$59.04

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line when activated, and send it through to your water dispenser in your refrigerator. To make this repair you will need an adjustable wrench, a quarter inch nut driver, and a sharp utility knife. Before you begin this repair make sure to disconnect the power supply to your refrigerator, as well as disconnect the inlet water supply from the back of the refrigerator. Note that this part may appear different than the original, but is an authorized manufacturer replacement.

$4.27

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, an...

$28.28

Meat Drawer Rail - Right Side

As you look into the fridge, this drawer support track is located on the right-hand side. This item is white in color and made of plastic. The drawer support track can wear out over time. The only tool required is a Phillips screwdriver. Empty out the drawer and remove it by sliding it forward. Lift out the shelf, remove the screw on the side of the shelf, remove the rail by pushing the rail forward and snapping out of place, insert new rail, and install the screw back in. Now the shelf can be put back into the refrigerator. The mounting screws are sold separately.

$53.89

Water Filter

Note: May need to order part # PS976499 to make water filter fit.

$8.38

Hinge Bearing

Sold individually.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with th...

$97.82

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

$33.81

Evaporator Fan Motor Kit - 120V 60Hz

The evaporator fan motor circulates air through the food compartment for efficient cooling in refrigerators. The evaporator is located in the back of the freezer and it circulates ...

$8.72

Closer Plate

$27.78

Water Dispenser Actuator

Once a glass is pressed against the actuator pad it will cause the dispenser to deliver ice or water when activated.

$27.82

Run Capacitor

The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refrigerator or freezer section will not start, if they are too warm, or if your refrigerator has become too noisy. Replacing the run capacitor is a relatively easy project. For this repair you will only need a 1/4 inch nut driver and needle nose pliers. Remember to disconnect the power and water supply line to the unit before you begin this repair. For full step by step instructions, simply click on the video below.

$28.86

Meat Pan Rail - Left Side - White

Mounting screws NOT included.

$29.05

Dispenser Crusher Housing

This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nut driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.

All Parts for the WRS23MF5ASH
1-14 of 292