WM2650HWA (F12A1FYP) LG Washer - Instructions

Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.

I received the locking device. I received an email from parts select with a repair video link. I watch the video and repeated the steps. Very easy and educational. Thank you for simplifying something I have limited experience doing.

I did repaired while looking at video at your site .thanks to your team ..

Went to U tube found several good videos relative to the problem, suggest you do the same. Heavy rubber diaphragm seal retainer spring VERY difficult to expand, bought a replacement spring with less tension and it worked fine. Plastic clip at the back of the cabinet does not have to be removed. Squeeze it and it will unlatch to free the hose, The part supplied was an exact replacement for the original, it worked just fine. Good luck.

I followed the instructions of your instant repairman. A Phillips screwdriver was the only tool needed. Thank you .

Unplug the washer! Turn off the HOT water valve. Remove the hot water hose at the connection on the back of the washer. Remove the two Phillips head screws holding the top of the washer. Slide the lid toward the rear until you feel it disengage, then lift it off, setting it aside.
Unplug the electrical connector on top of the hot water valve (just pulls off).using pliers compress the hose clamp, slide it away from the hot water valve and pull the hose off the valve fitting(it will have some water remaining so lift it up and secure it to the brace above the hoses).
Remove the two phillips head screws that hold the valve in place. Pull the valve toward the front of the washer to remove it and compare it to the new valve.
To install the new valve, reverse all steps insuring tight water hose clamp and electrical connection. Install hot water hose, plug it in and turn on water. Test run and check for leaks. Unplug it and reinstall top.

Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that.

E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.

I followed various tube videos. The vides were very easy to follow.
But the most important thing to have to do the job is washing machine spring removal tool. This tool I had to order it online unable to locate in store.

The web interface is nice, however in this situation it references the wrong part which was not known until the item arrived. Customer Service handled return, however I had to call LG directly to confirm correct part number (LG p/n 4866ER0004A = p/n PS3524040) but this was only after LG also gave wrong p/n. When replacement part arrived the internal concrete had a crack in it. The part is basically a plastic shell that is filled with concrete. However the opening (about 1 x 4) is left open and with the concrete having a crack in it the piece will vibrate together and continue to break down over time (which is what happened to the original one) Before installing I chose to fill opening with epoxy and a plastic layer, then covered with electrical tape to seal it in. I feel this item is poorly designed from LG. Additionally this item was poorly packaged by PS when shipping which caused the damage (it weights about 15 lbs and was allowed to float around in a large over-sized box filled with large air pillows). I have photos but no way to upload here.

-Unplug washer
-Turn off water supply
-Pull machine away from wall
-Remove two screws on the back holding the top panel in place
-Slide top panel toward the back and remove
-Unplug electrical conectors to the control panel, remove screws and take out panel.
-Remove lint trap plastic door cover bottom front left and screw holding plastic housing.
-Take housing out.
-Remove screw that is behind plastic panel holding front panel.
-Using spanner, release spring clamp holding gasket to the front panel.
-Remove top screws holding front panel on and take off panel.
-Remove hose clamp and hose at bottom of gasket.
-Release inner spring clamp on gasket to washer drum and take out gasket.
-Install new gasket and spring clap to drum.
-Reverse the order to reassemble.

Removed top of washer
Then removed front
Then reversible basket ,during spring depressed pliers
Put new gasket on inside flange first put spring back on
Put front washer panel back on and put screws back in panel holes
Put door seal on front flange and reinstalled spring on new door seal.Put too back on and finished clean up

remove 2 screws from top panel - pull top panel back and lift off washer. reach down on front side and remove wire harness that is attached to door lock assembly. remove the 2 screws on front of door lock,remove and replace with new assembly. attach wire harness and then tighten assembly with the 2 screws. replace top of washer panel and tighten with 2 screws.

Just removed the top cover only. Reached down and unplugged the door switch. Then removed the switch with 2 phillips head screws. Replaced with new switch. Reached down and plugged that new switch in. Problem solved!

removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.