Models > WM0001HTMA > Instructions

WM0001HTMA LG Washer - Instructions

All Instructions for the WM0001HTMA
61 - 75 of 154
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
A tore bellow
I went by the video
Parts Used:
Bellow - Gray With Drain Port
  • Danny from MOUNT AIRY, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Hinges, door lock assembly, frame door
Remove door assembly from the hinge, unscrewed screw from the panel. Leave couple screws to hold Hinges. Remove the rubber seal but stretching to spring out, not having rt tool (long nose plier). Remove rubber partially close to the hinge. Remove the Hinges and replaced it, then reverse putting together back. Use small screw driver to put spring tensioner back. Reinstall frame door to hinge, double check everything.
Parts Used:
Hinge Assembly
  • Julius from WINNETKA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The billows had two holes in the bottom part.
Removed the front and replaced the bellows. Also watched a YouTube video of someone replacing the bellows of a similar washer.
Parts Used:
Bellow - Gray With Drain Port
  • Robert from EXETER, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noticed small tear in hose bellows and leak during reassembly
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).
Parts Used:
Washer Hose with Bellows
  • Ryan from HIGHLAND, UT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was leaking.
After watching the video for installation of the bellow, I followed the suggested repair method and was able to repair my washer.
Parts Used:
Clamp Assembly Clamp Assembly
  • Memo from LA MIRADA, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak in top washer hose
Super straightforward to diagnose and repair.

There was puddle under the washer.

I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.

Two hose clamps to remove and replace, then replace the top and ready to go.
Parts Used:
Washer Hose with Bellows
  • Jason from S HAMILTON, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
WASHER WOULD NOT FUNCTION BECAUSE DOOR LOCK ACTUATOR (ORIGINAL) FAILED.
WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.
Parts Used:
Door Lock Assembly
  • BRAD from AUBURN, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would not run
replaced switch as shown in the video...Worked great
Parts Used:
Door Lock Assembly
  • kirk from WEST COLUMBIA, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Did not draw the water and did not finish its cycle
Remove where the water pumps are and remove the one that was damaged easily
Parts Used:
Washing Machine Drain Pump
  • saul from NEW YORK, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap dispenser broke
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
Parts Used:
Detergent Dispenser
  • Roger from LA CROSSE, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bought used, realized did not have a detergent dispenser.
Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work
Parts Used:
Detergent Dispenser
  • Lynly from Montrose, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not drain.
I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.
Parts Used:
Washing Machine Drain Pump
  • John from FENTON, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was not draining
It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done
Parts Used:
Washing Machine Drain Pump
  • ALEX from TULARE, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tub assembly main bearing was sized, and grinding. Wore shaft 16th down.
Pretty straight forward video located on YouTube. Video is about 30 min long. Watched it for an overview and did it myself being mechanically inclined.
Parts Used:
TUB ASSEMBLY,DRUM(INNER)
  • Jon from PHILADELPHIA, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spin cycle was shaking my house LOL
Just like it shows on You tube but one of the shocks did not come with the plastic pegs so i used the old one. I need to order the springs now and replace them.
Parts Used:
Shock Absorber Kit
  • Jennifer from MARYVILLE, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WM0001HTMA
61 - 75 of 154
Back to Top