Models > WGD9450WW0 > Instructions

WGD9450WW0 Whirlpool Dryer - Instructions

All Instructions for the WGD9450WW0
556 - 570 of 574
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
flame out
easy as pie !
Parts Used:
M Series New Style Coil Kit
  • john from glen head, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer worked but did not heat
Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.
Parts Used:
Dryer Radiant Flame Sensor
  • Steven from Garden City, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
very noisy
followed the you tube video, came apart ok, very bad lint problem. Vacuummed out extensively. Made repairs, very straight forward. Back together ok, still noisy but not as bad. May be the fan.
Parts Used:
Dryer Repair Kit
  • Christopher from Momence, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
couldnt find this model dryer on the whirpool part on their site
Found this part on your site very EZ bought it you shipped to my door got it when you said it would be here open it installed it propblem over glad i found you guys will use again Very good website Keep up the good work THANK YOU
Parts Used:
Lint Filter
  • clyde from Harrisburg, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
latch inside door popped out
Order one new latch, receive 2 spares. Pushed new latch in, re oriented the catch. was done in less than 5 min
Parts Used:
Door Catch Kit
  • zachery from snoqualmie, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The Dryer would make a squealing noise like a toddler while running.
We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.
Parts Used:
Idler Pulley with Bracket Idler Pulley
  • Ann from Phoenix, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer cycles but will not heat
removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.
Parts Used:
M Series New Style Coil Kit
  • daniel from mercedes, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer door was difficult to close
One small part of the hinge broke and made it difficult to close the door. Purchased the part, $91 with shipping, from PartSelect. It arrived within the week. Installed it within minutes. End of story!
Parts Used:
Door Hinge
  • Lora from Murrieta, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No flame
when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.
Parts Used:
M Series New Style Coil Kit
  • Rafael from SAINT PAUL, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Old lint filter had holes in it.
removed old one installed new one.
Parts Used:
Lint Filter
  • John from Massanutten, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No heat
Just like the instructions. Piece of cake.
Parts Used:
Igniter Kit
  • Randal from Fowlerville, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Noisy/Rattleing Tumbler
First i did some research on the internet approx.1yr ago.Just in case any problems like this or any other kind of problems should arise which it did.The whole thing is Easy all you have to have is some basic knoledge of how things work.All of this came "OFF" in (4) sections.After installing everything back it was as "Quiet"as the day we purchased it.Good for another 5yrs.Retired welder & "J.O.A.T.Julian San Antonio,Texas
Parts Used:
Dryer Repair Kit
  • Julian from San Antonio, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
dryer wasn't heating
Followed the parts select You tube video. Was helpful. Note the Ignitor kit is very sensitive. We didn't need an ignitor right now but purchased one in case the other 2 parts didn't help the problem. We took the ignitor ( wrapped in a bag) out of the packaging and it snapped in half without even touching the sensitive end. Note handle with extreme care.
Parts Used:
Dryer Radiant Flame Sensor M Series New Style Coil Kit
  • ERIN from RED WING, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer was throwing a E1 Error
Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).
Parts Used:
Thermostat, Internal-Bias
  • John from Indian land, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Door latch was broken
This dryer refuses to die and I am happy to keep it that way. Door latch was replaced in less than a minute using this kit. Easiest repair ever.
Parts Used:
Door Catch Kit
  • William from Champaign, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WGD9450WW0
556 - 570 of 574
Back to Top