WFW9150WW01 Whirlpool Washer - Instructions

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

Well first off the part is different then the orignal so it does not fit correctly. I removed the old bellow and its cicular spring clamps. On the new bellow there is not enough lip on the rubber for hte clamps to be put back on and hold the bellow in place so it still leaks out the door. if the part was a match it would work but since the part number was changed and the design was changed it now does not fit correctly. INstructions did not come withthe part so had to find them online.

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

It took a very long time to attempt to diagnose the problem with this type of washer, finally was able to get the diagnostic to run and it said it was the Motor Control Unit (MCU). After ordering the part which was easy, it was not the reasoning for the problem and I still cannot get this machine fixed. Returned the part with ease, just waiting for the refund to go through.

Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.

Perfect part...saved me hundreds on labor. Thanks!

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

The key to this repair is 1) lifting the front of the washer to access the bottom trim bolts, and 2) using lubricating spray around the outer bellows clamp area and 2 people to work the clamp into place.

removed retaining ring on front gasket, pulled gasket back, took out door lock latch, unhooked wires, then reversed method to replace.

the repair cost was about 1300$ from a repairman! and they wanted to replace the complete inside drum assembly, so i decided to break it down myself and i'm an average do it yourselfer 1. unplug machine 2. remove water hoses 3. remove the top 4. remove back panel and front complete 5. remove all inside connecting wires but leave them close as to make it easy to reconnect 6. take all three shocks loose from bottom of drum and remove all counter weights (concrete) 2 on front and 1 in back as to keed drum ballanced for removal and 7. remove the complete drum 8. set drum down door side down and remove pully and then all the metal clips with a flat screw driver and lift back portion of the outer drum up and remove. then the inner drum will be visable 9. take the 6 Torx (star) screws out of the drum support and remove! and semply reverse the process for assembly! taken photos of the process will help the assembly process as well