WED8300SW0 Whirlpool Dryer - Instructions

Ordered the fuse first hoping it was just that simple, watched the video for how to replace, first step was to take the back of the dryer off, well I order to take the back off I had to take off the Electrical Cord, as well as he top of the dryer. Only to find out he part I was replacing was not back there. Found the tech sheet attached within he dryer though, and as it turns out only needed to take he front bottom panel off. Without testing he continuity I was just giving this a shot, the Thermal fuse did no fix it, so I tried the high Limit Thermostat and Fuse kit still no luck. Took out the Element to find I was physically cracked in 2 pieces, replaced that and I was back up and running. And all parts were found in the bottom front panel of the dryer, so beware before you watch the video and take our whole dryer apart like I did.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Replaced Lint Screen

Replaced Thermal Fuse

Your website was wonderful--thank you so much! When I saw that 47% of the time this was the problem, I ordered it & it worked! This was a life saver for me! I will come back to this site anytime I have an appliance problem! Thanks again!

very easy had to do some rewirng.who ever had it before me bypassed the fuse and several other things.

Took screwdriver popped out old latch in cabnet. Took pliers popped out latch out of door. Snaped new latch parts back in.

Removed rear panel screws carefully removed panel with out disconnecting wire harness located thermal fuse removed 2 screws removed the 2 wires with needle nose pliers put new thermal fuse in connected the 2 wires carefully put panel back on and tightened screws turned on power and start got heat problem fixed

Had previously replaced the heater coil (purchased from PartSelect) and fixed the no heat problem. Should have taken advice given on this site and replace the thermostat and thermal fuse kit at that time. Since I knew how to remove the assembly it was easier this time. Just remove, unscrew the two parts and replace with the new ones. Reattach the wires and reinstall the assembly and it is now working again. Also vacumed the inside and trimed and replaced the exhast vent hookup for less restriction.

After trying to follow a very detailed description by another consumer, we googled our washer and found a site that showed step by step direction that took us through removing all panels and getting to the bellow easily. Not removing the proper panels, we found was making the job hard!I believe the site was applicance services...very helpful! Step by step literally!!Cost of parts through parts select reasonable.

I diagnosed the problem using the web page. It said that 60% of the people with my problem bought the Thermal Fuse. I unplugged the dryer AND cut the power at the fuse box. I used a screwdriver to remove the vent hose, a nutdriver to remove the back of the machine. The thermal fuse was right there. Removed the old one with a screwdriver, unplugged the wires from the old one and snapped on new one, and screwed it back in. Re-installed the back of the dryer and the vent hose and Whoila! It works like a champ.

This did not require a "repair", just a replacement. I want to say that the response time and ease of ordering were very good. I would not hesitate to use PartSelect again when needed. Thank you!

pulled out old lint filter. Put in new lint filter.