WDT790SAYM0 Whirlpool Dishwasher - Instructions

Easy as pie...bought the full arm spray from partselect.com. Scraped the melted plastic off the heating element with ease. Locked the new arm spray into position, and we were back in business. It was that simple.

I removed front bottom cover on dishwasher. The drain pump is on right front side. Very easy to remove and to install a new pump.

The dishwasher had to be pulled from under the countertop and the face at the base of the dishwasher required removal. The new piece was attached to the door spring, routed through the wheels and attached to the front attach point of the dishwasher. The face was reinstalled and unit was pushed back to under the countertop.

There were actually slots cut in the side to place a screw driver to strentch the spring to attach it to the cord and plastic end. But the spring would not stretch far enough so took the intiative and drilled another hole to place screw driver and pry the spring far enough to attach the replacement piece. After that it was done. Fairly easy as you have the other side of the appliance to look at and can tell how the hidge on the side that needed repair should go. Very very easy after hole was drilled in frame.

I simply disconnected the power line to the dishwasher and pulled it out enough to install the mounting brackets. The installation manual that came with the dishwasher described how to install the brackets and I simply followed directions.

Followed the video it was real easy

Pulled the dishwasher out to remove the broken link; attached the link to the spring; attached the spring to the frame; treaded the link around the lower part of the pulley; attached the link to the door; and treaded the link around the upper part of the pulley while pulling on the spring.

I followed the instructions from the partselect video and replaced the damaged door balance part. I ended up having to adjust the plastic wheel piece because the new strings were shorter than the original but luckily there was another screw hole to accommodate the shorter strings. I did replace both sides. Overall, this was a very easy repair thanks to partselect and now my door works great. I will definitely be using this site in the future!

Disconnected the water and drain lines, pulled the washer out of the cabinet cavity. At that point, the work area was fully exposed. Then just a matter of removing the old assembly and replacing with the new. Stretching the spring so the other end of the cable could be attached to the door was the only part of the project that took a little bit of effort. It took more time to disconnect the water lines and pull out the washer than replacing the broken parts on each side of the door.

Pulled dishwasher out went down looked at problems ,saw both springs out of place and disconnected from door. Rewatched your video . Went to work one problem I did not realize the door had to be down to hook cable plastic attachment to door . Looked at video again saw door had to be down hooked up done !

Removed screws from under counter supports with Phillips head. With small flat head screwdriver removed the bottom plate, adjusted the support feet upwards . Very gently pulled out dishwasher from cabinet , about 2-2.5 feet exposing lower sides and springs and old balance parts. With a nut driver 5/16 removed first side old part keeping nut screw, placed the dual wheel part keyhole notch into the hole and positioned the bottom and loosely secured the lower portion back into the hole with the nut screw.Then with the cord replaced the narrow part over the metal holder the way the old one was. Carefully feed the cord over /under as before , tighten the nut screw into place take the ring end and and hook it on to the spring that is very tight and hard to pull into place. This was the hardest step as I needed help because of the heavy duty spring. My 7yo granddaughter hooked the ring as I need both hands on the spring. I checked the part for being screwed in correctly , then repeated on the other side. Carefully pushed the appliance back into cabinet making sure any cord, hoses had not been pinched, adjusted the front support legs back into place , secured the upper braces, replaced the lower plate and it is perfect! It works better than after I had a handy man do this a few years ago. I am a 64 yo woman!

I watched the video on the web site and made the very simple repair. It was so easy that almost anyone could do it. Also, the parts arrived 2 days after I ordered them. The whole process was very easy and saved the cost of a service call.

exactly as your great video suggested.thanks