WDF110PABW1 Whirlpool Dishwasher - Instructions

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts

Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!

The old filter simply unscrews and the new one screws in.

It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.

Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

removed and installed cords with screw driver

Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

quick and easy replacement, without tools...

i ordered the wrong part and received the new part and credit for the old part, quickly...Plus, I was kept informed with e-mails....

excellent service...

My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!