Models > WDB745RES1

WDB745RES1 Westinghouse Dishwasher - Overview

Get Parts and Repair Help for WDB745RES1

If you know the dishwasher repair part you need, you can browse the list of all parts on the WDB745RES1, or you can search by name or part description. You can also find your part by where it is located on the WDB745RES1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for WDB745RES1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.45

Bottom Gasket

This gasket goes on the bottom of the dishwasher door. Note: Once the gasket is replaced and you continue to have water around the bottom corners of the door panel, you may need t...

Order within the next 7 hrs and your part ships today!
$10.68

Tub Gasket - Gray

The gasket provides a waterproof seal between the tub and the door.

Order within the next 7 hrs and your part ships today!
$5.91

Single Rack Roller Kit

This kit comes with one axel/clip and one wheel/roller.

Order within the next 7 hrs and your part ships today!
$22.57

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Order within the next 7 hrs and your part ships today!
$24.55

Lower Spray Arm with Shield

This spray arm is located on the lower half of your dishwasher. Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spr...

Order within the next 7 hrs and your part ships today!
$3.27

Heating Element Brass Nut

This nut is sold individually. It is used to install the heating element.

Order within the next 7 hrs and your part ships today!
$5.14

Dishrack Roller

Sold individually.

Order within the next 7 hrs and your part ships today!
$42.75

Detergent and Rinse Dispenser with Cap

The manufacturer has redesigned this part and it may appear different than the original, but will have the same functionality. This part releases the detergent and rinse aid into the dishwasher.

Order within the next 7 hrs and your part ships today!
$17.11

Door Spring

Sold Individually.

Order within the next 7 hrs and your part ships today!
$29.86

Silverware Basket

This is a basket for washing flatware or silverware in your dishwasher.

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from Inlet Valve

  • Customer: CHRIS from ROANOKE VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 487 of 492 people found this instruction helpful
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first ... read more

Lower Rack Roller missing

  • Customer: Sandra from Mount Vernon WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 362 of 364 people found this instruction helpful
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new. read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 120 of 131 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more