WDB212GBW0 Frigidaire Dishwasher - Instructions

After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!

Replaced the gasket

I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.

washer asm came off due too a bad plastic nut removed pump houseing and then put on new arm and reinstalled pump houseing,, seemed pretty stright forward,,

This could not have gone easier! As long as you get the proper parts it's a piece of cake. I wish everything was this easy!

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

This is a case of weak OEM design. Substantial (cup) weight placed on the rack will ultimately cause these wheels to break under load stress. My fix went slightly beyond the design by installing 8 cents worth of washers between the wheel and the screw head. That way any slack was reduced so that the wheels were less stressed at an angle. The rack now sits square and the wheels more true than design. I picked up some lock washers at local hardware store and flattened them out to fit smooth. The parts supplied by PartSelect were perfect fits to OEM. This is a truly easy repair. If your top rack keeps falling off the guides due to broken tub wheels this will take care of the problem. I will add that the parts that you can obtain through PartSelect are adequate without improvising. I just went for a more robust fix to the original design with additional washers. Hope this is helpful.

Got the parts in a DAY! Wheels were broken and worn causing top tray to slip off runners- new wheels were easy to put in-used the screwsfrom the old ones and banged out the job in about 20 minutes, including letting my son help. Thanks Partselect, you've hooked a new DIY'er (my son)

Removed old gasket and clean surfaces on tub and door before installing new gasket. New gasket has a small notch in the middle for top center. Install top then down sides for best results. Door gasket snaps into existing groove so no tools are required.

Took out the old and installed the new and ran the dishwasher, no leak. Problem solved

There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.

I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!