WCXR1070TBAA General Electric Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Roll pin had shattered destroying the clutch clip
The motor assembly (630 in the parts diagram) has a spring pin in the drive shaft to connect the drive shaft to the clutch. The spring pin had shattered. Instead of replacing the entire motor assembly ($365), I ordered a new clip from PartSelect, and a new spring pin from McMaster-Carr. Used a screwdriver and mallet to drive out the old spring pin and install the new one. Reinstalled the clutch and clip and everything was good to go.
Parts Used:
-
Alan from SIMI VALLEY, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
machine wouldn't agitate
took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....
Parts Used:
-
Bonnie from Erie, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
replaced agitator and coupling
-
Roger from Kelso, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The clothes have been dingy for quite some time.
I noticed the agitator would spin all the way around, in each direction. Also, the machine would make no sound, associated with washing, during that part of the cycle. I pulled the fabric softener reservoir off, with fingers on each side of the agitator, i pulled straight up and that gives you access to the coupling. Use a 7/16'" socket to loosen the nut, remove it and pull the coupling off. Press the new coupling on the splined shaft, tighten nut, and line up agitator with the grooves, push it down and replace fabric reservoir. Straightforward repair.
Parts Used:
-
Mark from Roanoke, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
water wouldn't shut off.
My 45 year old son did it in the shop, and it only took a short time before we were washing clothers again, and no water on the floor. The part came through the day after I ordered them. Thank you very much
Parts Used:
-
Ronald from Monroeville, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
Stripped plastic coupler spline
Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done
Parts Used:
-
frank from palm city, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The gear agitator had striped. Wouldn't spin the blades to wash the clothes.
I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.
Parts Used:
-
Gerardo from Mountain House, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!