WCSR2080B4CC General Electric Washer - Instructions

pushed replacement knob on shaft of dryer. machine works better than new. took less than 24 hours from time of order to time of delivery to my house.

Installed a new mixing value. Repair went quickly and easily. Repaired machine working great. Easy ordering and the prompt shipping impressed us Greatly!! Thank you!

at 1st, i call GE for service, but i have to wait for the next available field service engineer which is 7 to 8 days to come to my place to check on the washer. the cost is $99.00(non refundable) and then he will order the parts needed for repair another 2 to 3 days. then i decided to buy the parts myself online,and google the web on "how to fix the washer that stopped agitating" everythings in there,with video instruction. pull the agitator up and out by grabbing on to its base. inside, the knot was corroded and the o ring worn out,but really easy to remove with the 11mm socket. the coupling kit although looks different,fit perfectly. insert says its an upgrade of the old model. toss the old and replace with the new, no sweat! now it's shaking like crazy.

Removed the four torx-head screws on the top of the washer. Pulled the control panel forward. Removed the four screws on the back of the washer and the two screws that held the dual valve on. These six screws required a nut driver. Pulled the small hose off the old valve. Then reversed the procedure. Total time to replace the faulty old part was about ten minutes. With saftey in mind, disconnect the electrical cord and shut the water valves off at the wall.

Viewed the step by step how to and was able to complete repair all has worked well great info sight!

I replaced the Switch and Valve per the other instructions on this board. It took about 15-20 minutes. After replace, I have not had any overflows since then.

I followed the on-line video with just one exception and I had the old part off in less than 5 minutes. I ordered the part on Saturday afternoon and I had the part in hand by Wednesday morning at around 11:00 am. I spent less time installing the coupling kit than it took to take it apart and had 2 loads of clothes done before going to work on second shift. I would recommend anyone needing help contact Parts Select. They were great and very helpful.

The agitator is the tough thing to remove, I took a previous posters advice and used a rope and 2 boards to pull it up. I will describe it as many short ropes but it can be done without cutting the rope if you think a lot about it. loop the a rope under the agitator so its under 1/2, loop another rope under the other side. tie both loops so you can slide a board in each across the top of the washer. Then tie the 2 loops together on 2 sides down near the bottom of the agitator otherwise they will come out from under it when you pull. then slide the boards in the loops and lift up pulling up the agitator.That is the hard part. Remove the bolt on the coupling, and pull it off. The new one had to be lightly hammered on with a rubber mallet, then use the new bolt. the Agitator slide down and with a push down it popped on. Putting the new part on only took 15 min, removing the broken one took about 45 min. Washer is woking great now ! Saved over $100 or buying a new washer !

Took the front panel off and it looked like everything was OK with the transmission, etc. Pulled out the agitator and noticed that the coupler had stripped out splines. New coupler was a later design, but was backward compatible with the new bolt included. Spline slipped on with no problem and hold down bolt snugged down just fine. Snapped the agitator back on and was in business.

old dryer knob had lost its spring and would not turn on. simply pulled old knob off and replaced by pushing new knob onto shaft. voila! saved myself a service call.

1)Remove the 5 screws from the back panel to gain access to the dual inlet valve. 2)Disconnect the wire from the valve. Then, remove the screws the hold the valve. Then, remove the C-clamp from the valve to get it loose. 3) Then, reverse the procedures to install the new valve.

Removed the old part with a screwdriver and replaced with the new parts. As good as new!!