WCSR2070T2WW General Electric Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
hole in hose
-
hirfa from lake worth, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
I bought this second hand and it had no hose
I watched the video you provided and I could't believe how simple it was. I'm 67 yrs old and I just followed the video instructions.
Parts Used:
-
Maryellen from Englewood, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Wouldn't agitate.
Took the front panel off and it looked like everything was OK with the transmission, etc. Pulled out the agitator and noticed that the coupler had stripped out splines. New coupler was a later design, but was backward compatible with the new bolt included. Spline slipped on with no problem and hold down bolt snugged down just fine. Snapped the agitator back on and was in business.
Parts Used:
-
Irene from Seymour, CT
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
water wouldn't shut off.
My 45 year old son did it in the shop, and it only took a short time before we were washing clothers again, and no water on the floor. The part came through the day after I ordered them. Thank you very much
Parts Used:
-
Ronald from Monroeville, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
Washer was not agitating
I used the video instructions sent to my email and everything worked perfectly as instructed.
Parts Used:
-
Maud from Ellicott City, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
machine wouldn't agitate
took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....
Parts Used:
-
Bonnie from Erie, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Stripped plastic coupler spline
Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done
Parts Used:
-
frank from palm city, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
old knob broke
Opened the package - put it on just like the old one. Didn't take 5 minutes. Good as new.
Parts Used:
-
Jacquelyn from Bokoshe, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The gear agitator had striped. Wouldn't spin the blades to wash the clothes.
I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.
Parts Used:
-
Gerardo from Mountain House, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!