WCCB1030Y2WC General Electric Washer - Instructions

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

replaced them & working fine now....

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

1) Researched internet for parts to make repair
2) Tested the cold side to make sure the only problem was the valve.
3) Ordered part from PartSelect
4) Made repairs after going to hardware store to purchase a set of torx bits to loosen the front panel so I can replace the dual valve assembly.

Only tools needed #1 Phillips and #15 Torx

Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

Pulled front panel of washing machine, removed hose, installed new hose, and wipped up water.Simple!!!

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

I had to take out the front panel to access the Tub. Afterward the work wasn't hard.

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.

I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.

The front panel has to be taken off to access the washing machine pump. To do this I used a putty knife I inserted the putty knife in the slot at the top of the front panel where it meets the top of the machine to release the clip that holds the panel in place. Once the panel is off the pump is mounted to the bottom of the machine with two screws. There are also two hoses attached to the pump that need to be taken off. Before you do this you have to get as much water out of the machine as you can to minimize the amount of water that will come out when you disconnect the hoses. My recommendation is to replace the spring type hose clamps the manufacturer uses with a screw type hose clamp. These are much easier to put back on once the hoses are in place. You are not fighting the spring clamp while trying to put the hose on in a confined space. Then put the front panel back on. This may take about a half hour if you do not have too much clean up because you didn’t get enough water out of the machine.

(As I am an older female, I used YouTube to review the repair before trying it. YouTube scared me, the actual repair was much easier) I removed the agitator from the washer which revealed the agitator assembly held in place by a bolt. After removing the bolt, the assembly was lifted off the spindle. I cleaned the grime off the agitator, the spindle and the bottom of the washer basket. New agitator assembly was placed onto the spindle and pushed down. There was a distinctive click when it slid into place. I replaced the bolt to the top of the assembly. tightened it down, then slid the agitator over the assembly, matching grooves to teeth until that also slid into place with a click. It honestly took me longer to clean the grime than to change the part. Agitator is working perfectly

Pull off the agitator. Remove 1 bolt on coupler pull off coupler. Slide new coupler onto spindle. Replace bolt. Line up and slide on agitator. Seat it firmly in place. Done. Took all of 2 minutes.