Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Capacitor failed (cracked, split, and melted a little), washer would not spin and laundry room filled up with smoke
Went to PartSelect website, troubleshot the problem I was having for the model washer I have. Ordered part, once it arrived, I had it installed and all back together in less than 30 minutes. Washer has been running with no problems since the repair. PartSelect is awesome!
Washer did not drain completely with water on floor, drain pump frozen.
After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.
The wife told me that the wash just wasn’t coming out very clean.
The wife told me that the wash just wasn’t coming out very clean. So I went to check it out and found that the agitator was just moving freely. Upon closer inspection I found that the coupler had stripped. I was unable to get the agitator free from the coupler so I had to drill out the inside top of the agitator in order to get at the bold that held the coupler in place. Once I got that out the rest was real simple. Just bolt in the new coupler and snap in the new agitator into place. That can be harder that you think. I used a block of wood laid across the top and just tapped it with a hammer to set the unit in place. Make sure that when you take it apart to save the bolt and the old cap unless you ordered a new cap.
Use paint scraper to release spring tabs holding front cover on.
Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.
R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).
IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.
Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.
Thanks to your great web site and help video I got this fixed in less than a minute. Literally less time than it took me to watch your helpful video. Don't know how to thank you - keep up the good work!
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. put the new part in and that was it.
Removed 4 screwes on the top of the washer. Layed down the control panel and there was the inlets. Removed two screws and loosened the hose clamp. removed and installed new part. It did the trick. No more problems.
used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.
1)pump leak damage,2) water over fill and leak water out the top
First I disconnect the power and then I pull the front cover and replace the water pump, drain hose, and the inlet hose this was fixed and straight easy job.My second problem was the overfill problem witch I took the knobs cover and I replace the water level switch.This job was also easy but did not fix my problem.
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help. sincerely, a satisfied customer
R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.
Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.
Unplug machine, verified the hot water line to the washer was clear. Used screwdriver to remove top panel from washer. Removed faulty (rusted) temperature switch from seating. Then removed each of the wires from the old switch with needlenose pliers and placed them on the proper area of the new switch. Placed the switch back on the panel and screwed the cover back on. Then plugged the unit back in an tested the hot, cold and warm settings. Easy fix.