Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven light stays on when door is shut.
I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.
Oven door latch was bent and did not release or lock
Had to disassemble the top of the stove and the control panel on the front. I took digital pictures as I disassembled so I could refer to them when putting the stove back together, especially when disconnecting wiring. It took about 3 hours, but most of that time was spent thoroughly cleaning 16 years of baked on grease from places that are normally unaccessible. The new latch works great - the wife is happy!
tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!
For safety I Unplugged the machine Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan. I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived. I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my
Disassembly - Took the back bottom plate off. - Removed hoses. - Removed pump with pulley (3 nut screws) - Removed belt
Installed new parts - Installed pump with pulley (3 screws) - Installed belt by placing on 2 small pulleys, then turning onto the large pulley (used a screwdriver to help align over pulley for leverage). - Replaced hoses - Replaced back plate.
Washer made a loud noise during spin-eventually stopped spinning
I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.
The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.
Open the top of the washing machine by using a putty knife to release the latches at the right and left side. Prop up the top so it doesn't fall while working. Remove the inlet hoses and put in bucket to catch water. Remove the two screws that hold the inlet valve in place. Remove the wires from the inlet valve. (One of the spade connectors one wire broke and I had to replace it.) I used needle nose pliers to pull the spade connectors off. Remove the outlet hose. Throw out old valve assembly. Attach hose to new valve assembly. (My old valve assy outlet was slightly smaller in diameter than the new valve, but I was able to get the outlet hose to stretch enough to fit--couldn't use old spring clamp though, but new valve came with a hose clamp--worked fine.) Attach wires same way as they cam off old valve. Position and use the two screws to screw assy back into back of washing machine. (The screws had to tap the holes on the valve, so start out a little hard.) Reattach the inlet hoses and check for leaks. I also ran both the hot and cold in a cycle and the reraised the top to check for any leaks internal to the machine. Pus the top back down to engage its fastening clips. Job done. My washing machine is 23 years old.
The Old Hinges broke off and the door would not stay closed
I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!
Easy as pie to do this repair. You first remove the 2 screws holding the element in. Then you carefully pull out the element and remove the wire clips at the ends. Just reverse the process with the new part.
By the way, I ordered my part from parts select on a Friday afternoon and it was on my doorstep Saturday morning..... and this was with regular delivery! I would buy again in a heartbeat from parts select. Joe Golub
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.
After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy
