Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bake element not working
Our oven is at least 30 years old and the parts are not even available through the manufacture anymore. A new stove would cost well over $1000.00. Jen airr is the only down draft stove available. So the repair was much more affordable that the alturnative. So thank you to part select for providing this service. The repair was simple. This is coming from a 36 year old female who has been around electrical work, but never done any myself. My husband was out of town and I felt I could do the job. I first made sure I had another adult present. I turned off the power to the oven. I then removed the visible screws to the element plate (2 on top and 1 in lower middle). I then pulled the element out enough to get behind the plate and feel the screws that were connecting the wires to the element/ground. Again 3 total. The oven space is very small and difficult to work in. I had to do a lot by feel. Once the old element was free I just exchanged it for the new one and reversed the process, making sure all the wires were tight. I then turned the power back on. Turned the oven on, it smoked lightly for a moment and turned red hot. Over all it was extreemly simple.
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.
oven selector switch was tripping the circuit breaker
Made sure the circuit breaker was off. Labeled the wires and then disconnected them. Removed the old switch. Ordered the part using the diagram on-line, very easy to identify part and order it. Part arrived earlier than expected using standard shipping. Reconnected wires using labels taped on the wires. Turned on the breaker and it worked.
temperature probe insulation broken down so short circuit
As the probe is a plug-in item that would normally be out of the oven, there was nothing more to the repair than checking that the new probe plug fitted the socket and that it was detected by the oven. Then the old probe was consigned to the trash.
Everything checked out, and the probe was used satisfactorily within a couple of days.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I did a continuity test and determined the old element was bad - ordered the new one and put back the screws. All done!
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I had to use a mirror and flashlights to see in the back of the oven to replace the screws in the new element. It was very close quarters and difficult to see behind element plate.
After the old element kicked the bucket with a final loud buzz, it was time for a new element
I turned the breaker to the appliance off in the breaker box. Took a mirror and a flashlight to figure out what type of tools I needed. Turned out all that was needed was a phillips screw driver and a pair of vicegrips as the front mounting screws were in pretty tight. Disconnected the element mounting plate, pulled the element forward just a few inches to where I could get to the wire connectors and unscrewed them. Connected the wires to the new element, pushed it back into place and refastened the front mounting plate. Turned the power back on to the oven at the breaker box and turned the oven on the check the element and it worked.
The oven on the 40 year old JennAir range stopped heating. It took more time to locate the model number D120 and conduct part/price search than the time it took to install the correct oven bake element from PartSelect! We read all the comments posted by others. We did not remove oven door. The old element had only 2 screws instead of the 3 reported by many. We followed the sequence--Power off at box; unscrew old element; pull out about 3 inches; disconnect wiring; used telescoping mirror to assist; connect wiring to new element; position new element; install 2 new screws; turn on power; turn on oven -- SUCCESS -- heating better than before. Thank you PartSelect.
Pulled out the old one-couldn't find it ANYWHERE that was a comparable match except for partselect. shut off breaker to oven-put in the new one-hard to reach in due to limited space and hard to see due to sticking your head in an oven.used a mirror/flashlight to see behind element to unscrew and screw it back in.Other than space restriction and light-pretty easy. Works great! Thanks for HAVING the part!! :)
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
First I removed the two screws that hold the element in place. Then I pulled the element out about 2 inches & disconnected the two wires, Then I removed the ground wire. I then wired in the new element ( this was the only tough part of the process, because I had a very tight space to work in- less than 2 inches.