Models > VE30CW4 > Instructions

VE30CW4 Tappan Range - Instructions

All Instructions for the VE30CW4
46 - 60 of 106
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Parts Used:
Main Terminal Block Kit
  • Barbara from WICKENBURG, AZ
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
high power awful smell
raise top of stove unplug burner plug in new one done
Parts Used:
Surface Element - 8 Inch - 220V
  • jim from gorman, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced terminal block for element
followed the video provided on line which was very helpful..
Parts Used:
Terminal Block Kit
  • Donna from UNION, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Parts Used:
Terminal Block Kit
  • Chuck from EVANSVILLE, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Parts Used:
Terminal Block Kit
  • Robert from PRAIRIEVILLE, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Parts Used:
Chrome Drip Bowl - 6" Drip Bowl - 8"
  • Helen from PAWLEYS ISL, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rusted Drip Bowls
This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.
Parts Used:
Chrome Drip Bowl - 6" Drip Bowl - 8"
  • Carolyn from OCEAN PARK, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven door hinges were worn out.
Removed the storage drawer to access the door springs.Removed the worn hinges and installed the new hinges,connected the springs. Removed the oven door before anything else was done.The could not have been any simpler .
Parts Used:
Door Hinge - Left Side Hinge - Right Side
  • Gilbert from Claymont, DE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Parts Used:
Surface Element - 8 Inch - 220V
  • Dan from CHEWELAH, WA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Can't regulate burners
Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same
Parts Used:
Burner Switch Kit
  • Pam from OCKLAWAHA, FL
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
OLD STOVETOP COILS
LOOKED FOR MODEL# OF STOVE.. ENTERED MODEL # IN PARTS.COM SEARCH.
MATCHED COIL AND DRIP PANS
ITEM NUMBERS AND SIZE.
PLACED ORDER.
ARRIVED FOLLOWING WEEK WELL PACKED.
PULLED OUT OLD COILS/DRIP PANS.
PLACE *NEW* DRIP PANS IN FIRST. THEN PUSH IN *NEW* COILS
**NO PAID INVOICE WAS RECEIVED**
Wed4/24/2024
Parts Used:
Surface Element - 6 Inch Surface Element - 8 Inch - 220V Chrome Drip Bowl - 6" Drip Bowl - 8"
  • SANDY from TOMAH, WI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed new drip bowls and 2 new elements
pulled them out and replaced them
Parts Used:
Surface Element - 8 Inch - 220V Chrome Drip Bowl - 6" Drip Bowl - 8"
  • kathy from DAVIS, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
Parts Used:
Surface Element - 6 Inch
  • Kenneth from LANOKA HARBOR, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would cutoff intermittently
Pulled out old burner/inserted new
Parts Used:
Surface Element - 8 Inch - 220V
  • Joseph from FREDERICKSBRG, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowls needed replacing
Removed the old ones and inserted the new ones.
Parts Used:
Chrome Drip Bowl - 6" Drip Bowl - 8"
  • Doris from SUN CITY, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the VE30CW4
46 - 60 of 106
Back to Top