TGF367CFTA Tappan Range - Instructions

order pcs fit perfect.

Disconnect appliance from electricity source! Removed oven grates and the solid oven floor by removing the two screws and lifting up. Removed the piece of metal covering the oven igniter. Unscrewed oven igniter, snipped the wires close to the old igniter (read some of the better descriptions on how to do this). Reconnected new wires to the existing ones and used the ceramic wire covers that came with the new igniter and pushed the wires back through the opening in the rear of the oven. Screwed the new igniter in place. We actually had to unscrew the little metal box on the back of the oven to get to the wires which was easier to work there with connecting the wires. It was a little difficult reaching into the stove since we didn't remove the oven door.

The stove was older so the burner was hard to get out. The small screw heads broke off, so I had to carefully center punch and drill out the screw bodies. The igniter screw was also frozen in the pot metal burner. That screw requied drilling and tapping with the installation of a new 6-32 screw. Once the burner was refurbished, the igniter mounted easily. Afte attaching the gas line and igniter wire, the burner worked great.

Checked internet for possible reasons why oven would not heat.

Found Partselect.com website. Searched and found that ignitor was probably the problem.

Put in my oven model number and found ignitor. Ordered ignitor.

When new ignitor came in I simply removed two screws that held old ignitor and disconnected two wire.
Put new ignitor on, replaced screws and wires.

Repair done and oven works great.

i had to remove all the broken glass then removed the metal that was holding the glass. set the new glass in the metal strips and screwed it back togethr. i also had to remove the frame from the door in order to get to the inside glass. then i had to put the door back together.

I removed the broiler burner assembly held in by 5 screws across the inside top of the oven, as I removed the assembly the igniter slid out from the back of the oven and was attached to the assembly with a cannon plug, I disconnected the cannon plug and removed the whole assembly out of the oven and replaced the igniter which was attached by two screws and reassembled in the oven. Where I live in remote Alaska calling a repair technician is not an option, either figure it out or have a new appliance barged in.

First, I want to say how WONDERFUL your service was. I needed more info on a part and your phone rep. e-mailed me a picture of the part from which I was able to be sure it was the right part. I ordered the pard one day and they were delivered to my door the NEXT DAY....talk about service!!!

My husband did all the replacing, he had no problems with any of the 3 items he replaced, he said they were all easy to replace. They all work great. Thank You!!

removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

The repair was fairly easy. The oven door was attached to a spring arm that had one screw holding each arm to the door. Once off, the outside set of screws were removed and saved in a small dish. Each section had 6-10 screws, to it's best to keep each set separate from each other. Each of the three layers (of the door) came apart easily by removing the screws for each section. The inside (broken glass) lifted out, was replaced, and the sequence was repeated in reverse. During the reassembly I was able to clean the other layers of glass that had gotten build-up on them over the years. Total time start to finish was about 30 minutes. Only tool required was a screw driver! Probably saved 100+ dollars!

Our original oven ignitor went bad. The gas supply won't even open, unless the oven senses the proper voltage / resistance across the ignitor, so that gas won't be flowing without ignition.

PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.

On to the actual repair:

I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.

I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.

Oven fired right up!

Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)

Thanks, PartSelect!

thanks to you 'r assistsnce First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, and changing the regulator was just as easy.

no need to remover burner. Lift top up use a 1x4x5" to hold top up. Use short #2 screw driver remove screw and replace with new igniter

Slide out the old; slide in the new!

I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!

I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.