Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
stripped pinion gear
I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.
Erratic starts and direction of ram. Switch tested bad.
Ordered part and received it in two days. Unplugged the compactor from wall outlet. Removed two screws holding control panel in place, marked proper wire location on rear of panel, disconnected push-on terminations from start/run switch. Removed knurled nut holding start/run switch onto the control panel and substituted the new switch. Reassenbled everything in reverse order to disassembly and plugged power cord back into the wall outlet. No further work required.
The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to make a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.
I removed 3 screws from the back and 2 smaller screws from the sides. I removed the broken handle, installed the new handle and inserted the 3 screws. The 3 screw hole aligned perfectly. The replacement part did not have predrilled holes for the 2 side screws so I drilled the holes and inserted the 2 smaller screws. Job done in short time.
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
compactor wouldn't compact
bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.
The part that doews the actual compacting would not move correctly. The machine would not stop because the part never contacted the spring loaded switch. I had known about this for about a year, but put it off until it stopped working altogether. I ordered 2 power nuts and rec'd them in B.F.E. Alaska in about 5 days. I quickly replaced the parts and the machine works like brand new again. I estimate this compactor to be at least 10 -15 years old and replacing the occassional part once in awhile is a lot cheaper than buying a new compactor.
remove drawer remove two phillip screws lift off front panel remove wiring and plug into new switch.slide switch through the hole in panel install nut reinstall panel screws and drawer job done.
Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.
refloored the floor and so the unit would not come out. had to cut tile, broke edge off of formica counter but once the unit was out a piece of cake. 6 self tapping screws removed , right on the top, two screws holding the cover for the power nuts, replaced broken nut, leveled ram, replaced nuts and ready to slide back in. After thought, I had one nut on hand from a few years earlier. I ordered two new nuts and now i am going to pull the unit again and replace both nuts. thought being a longer period before having to do this again. The unit was put in in 1981 and used continuously.
Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.
Trash compactor would not turn off at end of cycle and made a grinding noise and some vibration
I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screws from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .
Drive motor would not turn off after completing cycle
Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.