Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
lower back element stopped working
I got the model number and ordered a replacement element from partselect, was shipped quickly and I installed it in about 30 minutes, it now works great
First I cut off the power to the stove and double-checked to make sure no current was flowing to the unit. There were two screws attaching the bake element plate to the oven. I unscrewed the two screws and carefully pulled the bake element away from the oven exposing the contact wires. I carefully loosened the wire contacts from the bake element, slid the bake element off the contacts and then slid the new bake element onto the wire contacts. I gently clamped the contacts onto the bake element, pushed the wires back into the back of the oven and screwed back the bake element plate onto the interior of the oven. I turned on the power to test my work and I was done.
the element did not turn compleatly off, the on light stayed on.
removed the screws holding the back metal panel, this exposed the wires to the switch. tested the wires to find that they were live when the switch was in the off position. ordered a new switch. UNPLUGED THE STOVE. removed the knob on the front of the stove. this exposed 2 screws, removed screws and the switch came away from the stove. removed each wire from the old switch and replaced them in the same position on the new switch. inserted new switch into the stove and attached the 2 screws. replaced back panel and pluged in stove. all tested well
First, I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires This was challenging; the element uses blade connectors that are difficult to grab, and I didn't want to damage the connectors with pliers. Strenuous wiggling eventually worked. After that, I just reconnected the blade connectors to the new element, pushed the wires back in, and tightened the two screws.
It was fortunate that I saw a red spot on the element. When I removed it, I noticed a hole had been eaten part way through the old element. I was probably weeks away from a fire.
We felt the only possible problem could be the switch assembly. I removed the switch panel, removed the wires from the old switch, one at a time, removed the old switch assembly and installed the new switch assembly. The extended stem did have to be snapped off (per your instructions) and that too was a very simple task.
Replacement was relatively easy. Oven door was pulled off hinges after removing 2 mounting screws nearest the hinges. After shutting off power at the breaker, screws (2 each) holding elements were removed. Elements were pulled into oven ~ 4 inches exposing wiring and clips. The clips pulled free with just a little wiggling by hand and were easily pushed back on by hand. Then reverse to finish.
Socket Lite come with clips attached to the outside of the housing. After you unhook the 3 lead wires that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you snap in the new unit. Attach the 3 wire leads, put a oven bulb in the socket end, and the install the light cover
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Pull unit away from wall. Unplug power remove topmost four screws from rear metal cover Pull knob off switch shaft. Remove two screws holding switch to panel. Break off shaft of new switch to correct length. Remove each wire from old switch and attach to Corresponding lug on new switch. Reattach the new switch to the panel and reverse the first four instructions.
I first removed the two screws (located on the inner side of the door about halfway from the top) which hold the hinges to the door. With the screws removed, I was able to remove the entire door by grasping the door on each side and puling up and sliding the door away from the hinges.
The rest involves deconstructing the door by removing the screws and layers of metal liner layers and frames until you reach the inner glass.
You're likely to get anxious about remembering where all the screws go when reassembling, but if you lay out the screws in the same orientation they were in prior to disassembly, you should be fine.
1 had 2 large burners not working at all, and was cooking everything on the 2 smaller burners
It was so simple to repair - all I had to do was slide the older burners out and slide the new ones in - it took less than 10 min to complete the whole job! No tools used at all.
8" Burner element intermittent, unable to control.
Easy.... UNPLUG THE STOVE FROM THE 240 VOLT OUTLET & READ THE DIRECTIONS THAT COME WITH THE NEW PART !! Removed upper rear cover panel 8 screws & removed panel, removed knob & 2 screws from front of control unit (on the control panel), pulled the control off the panel from the rear, removed the wires on the rear of control & connected them to the SAME terminals on the new control (one at a time). Then installed the new control by reversing the procedure above. Took about 15 minutes. IMPORTANT HINTS: 1) Make sure you save the little black pressure clip from the control stem on the new control, if you need to break-off the little part at the end of the stem. You will need to push the clip back into the recess on the new stem, in order for the knob to stay on the stem when you put it back on; 2) Use a needle-nose plier to pull the wire clips from the old control terminals & push them onto the same terminals on the new control, one at a time so the wiring is correct.
Inside brass liner in socket came out when bulb was removed. Apparently had welded itself to the base of the bulb
Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.
Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!