All Installation Instructions for Tappan Range TEF351EWJ

Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

Parts Used:

Temperature Sensor

James from S CHESTERFLD, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Heating element for a frigidaire stove top broke

Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.

Parts Used:

Surface Element - 6 Inch

Rebecca from ASHEVILLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I damaged surface element left kettle on without water in it

The repair was really easy. All I did was unplug the surface element and plug in the new one.

Parts Used:

Surface Element - 6 Inch

Terminal Block Kit

Kenneth from LANOKA HARBOR, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven bottom panel rusted away

Removed two screws removed and replaced panel.

Parts Used:

Bottom Panel

Ron from CINCINNATI, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowels needed to be replaced

I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Francine from OTEGO, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Repaired Oven Range Light Bulb

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Parts Used:

Light Bulb

Alan from SAN MATEO, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven temp was not heating up to desired temp and using an oven thermometer to confirm

moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved

Parts Used:

Temperature Sensor

philip from CLIFTON, NJ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove was dropped and had broken, bent frame and adjuster feet

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Parts Used:

LEVELING LEG ASSY

Paul from PORT ORANGE, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven wasn’t heating

Used instruction video & replaced part.

Parts Used:

Temperature Sensor

Felicia from FORT MILL, SC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners getting too hot.

Watch video. This oven had the connecters that popped off and on which made this task easy.

Parts Used:

Infinite Burner Switch

Infinite Burner Switch - Small Element - 240V

Leslie from CONCORD, NC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

F10 code going off

Went well, and working thank you ??

Parts Used:

Temperature Sensor

edward from BRISTOL, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

run away temp

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

Parts Used:

Temperature Sensor

James from ELKHORN, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I could can not control the burner

was easy open the back side of the range and change the part, the only issue was the wire I used the diagram

Parts Used:

Infinite Burner Switch

German from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner switch had gone bad.

I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.

Parts Used:

Infinite Burner Switch