Models > TEF351EWB > Instructions

TEF351EWB Tappan Range - Instructions

All installation instructions for TEF351EWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF351EWB
106-120 of 516
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn't heat

  • Customer: KaShira from Wilmington OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!

bake element burned out

  • Customer: Kenneth from Wantage NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into back wall of oven. Don't know what you would do then.

Banking Element needed replacement

  • Customer: Mitchell from Sebring FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 1 of 1 people found this instruction helpful
For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!

oven wouldn't heat

  • Customer: Heather from Londonderry OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
First the power was turned off, then the oven door was removed. The two screws on the bake element were removed. Then the element was pulled out so that the wires were exposed, about 3 inched and disconnected. Put the new element in and placed the wires on the ends and pushed it back in place, put the 2 screws on, put the door back on. Turned the oven on and everything back to normal !!! Thanks part select for getting my part here so quick.

The bake element had been heating erratically, and finally broke when I knocked it while wiping out the bottom of the oven.

  • Customer: Rod from Forestville CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 2 people found this instruction helpful
I turned off the curcuit breaker, then removed the two screws holding the element in place and pulled it out to expose the connecting wires. The connectors resisted coming off at first but gentle pressure w/pliers did the trick. Then they slipped onto the new element easily, and I pushed the tips of the element back into the holes, replaced the two screws, and flipped the circuit breaker back on. Good to go in about 20 minutes!

Bake element failed

  • Customer: Una from Milwaukee WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
I ordered the part and received it in two days. Using only a nut driver, (and after tuning off the electrical supply to the range), I removed the element, pulled off the attached terminal attachment, replaced the new element, connecting the new one to the wire terminals, replaced the nuts, turned on the power and was once again in business. Thank you. (P.S. I am a 70 year old grandmother)

Oven wouldn't heat, but broiler would

  • Customer: Rolland from Portland OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 1 of 2 people found this instruction helpful
When I removed the two screws, I discovered that one wire attached to the element was not attached. I had to open the back of the range (sheet metal screws) to find the wire, which was burnt and melted when I got to it. I had to run to hardware stroe to get a new connector, but once I had that the whole thing popped together quickly. I attached both wires to the element, screwed in the screws, and voila!

The oven temperature would not exceed 200 deg.

  • Customer: Michael from Steubenville OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
Removed the retaining screws in the clips attached to the element in the oven, and then remembered to OPEN the breaker before proceeding. Pulled out the bad element, removed the wires, and reversed the steps to install the new one.

Heating element separated into three peices

  • Customer: Walter from Syosset NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 2 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire connectors from the lugs on the element. I then connected the new element in reverse order. Then I tested the new element by setting the controls to bake. That was the end of the repair rprocess.
Thank you for your parts and delivery service.

Element was burnt and now working.

  • Customer: Sam from Lexington KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
I turned off the circuit breaker. Unscrewed the two screws holding the bake element in place. Next, I pulled the element out and disconnected the wires. Reversed the process and I was done.

I ordered the part from PartSelect.com and had it in my hands in less than 3 days--wow!!! Super fast shipping and the part worked perfectly.
Thank you!

Burnt Out Bake Element

  • Customer: Lesley from Schenectady NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
We viewed the online video and replaced the element ourselves in less than 15min. No drama, no delays and no service costs. Thank you so much!!

I could can not control the burner

  • Customer: German from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
was easy open the back side of the range and change the part, the only issue was the wire I used the diagram

element burned out due to spill.

  • Customer: william from kerrville TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
I took the racks out then took the two mounting screws out with a 1/4 in. nut driver.

Thanks

WM T BROWNE, JR

Turned oven on and it flashed & arced & would not heat up, but oven light was still on, but dimmer.

  • Customer: Albert from Gueydan LA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
Most of the time I attributed to this repair was cleaning the stove in, around and in back of it after unplugging the stove. Next I used a nutdriver to remove the two retainer screws on the back of the oven. Then pulled the coil out with the wire connectors about 6 inches and pulled both of the connectors off old coil attached them to the new coil putting it back in place lining up the screw holes installed screws & tightened them up. I finished by touch up cleaning the coils of body oils due to touching the coils during install. Plugged it in, turned it on and viola! Thanks, sure beats the local appliance mechanic @ $45+/hr. Thanks again, I will look you up the next appliance that fails.

heating element was cracked, oven would not heat.

  • Customer: Tonya from Cokeville WY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 2 of 5 people found this instruction helpful
I used a small wrench, It was very easy to remove. once I removed the screws and disconnected the plugs from heating element then had to remove the back cover of stove so i could plug in new element. but was very easy. I am a single woman and was worried that it would be difficult to change. it only took me 20 minutes.
All Instructions for the TEF351EWB
106-120 of 516